Jump to content
SAU Community

R32 Rb25 Conversion

Josh_TypeX

By Josh_TypeX,
in Engines & Forced Induction

 Share

Recommended Posts

Josh_TypeX Proficient

Josh_TypeX

Posted
Posted

Alright, just thought I had completed my Rb25 conversion. The car starts, runs and drives, but I have a couple issues.

1. Wiring. Thought I had completed the wiring using the MANY sources going round. However I have no accessories. No radio, parkers (have head lights), no tacho (have speedo), no dash lights etc. The only doubt I had about my wiring was not using the green eccs relay from the 32 loom. Did I need to? Antone know what the problem could be? Note, there was a large spark when connecting the battery, however there are no blown fuses.

2. Noises. The main one of concern is a screeching/whining coming from somewhere. Sounds like near the gearbox, possibly the starter motor. It was really bad when i first started it and became worse with the clutch in. I used my old rb20 box, clutch, flywheel and starter during the conversion. When I was swapping the flywheel and clutch across I was worried about being able to align it properly, however I did my best and was able to align it with the gearbox in the end, not sure if this is relevant at all.

I'm so tempted to give up on cars all together at the moment, the only thing keeping me going is the fact that when I was driving it the noises stopped and it pulled hard. Oh, and my wipers work :) lol. Please help me get this thing working!

Thanks,

Josh

Link to comment
https://www.sau.com.au/forums/topic/296824-r32-rb25-conversion/
Share on other sites
Josh_TypeX Proficient

Josh_TypeX

Posted
  • Author
Posted

btw, using a series 2 motor and loom and I didn't use either relay, not just eccs.

Another thing I though of; The thick white/purple wire from the plug near the air box I left unconnected since series 2's don't have a separate Power to IGN Coil relay, should it have been connected to something else instead?

BH_SLO32 Proficient

BH_SLO32

Posted
Posted
btw, using a series 2 motor and loom and I didn't use either relay, not just eccs.

Another thing I though of; The thick white/purple wire from the plug near the air box I left unconnected since series 2's don't have a separate Power to IGN Coil relay, should it have been connected to something else instead?

Josh, I am certain you have blown your main 75A fuse. Look at it CLOSELY as it is often not easy to tell. My guess is when you put the battery feed onto the alternator you you have earthed it against the alternator. There should be a plastic cup which prevents the feed from the alternator earthing against itself. This sometimes comes off so double check. I am talking from experience!

The other noise you were referring to is hard to tell from what you have described but was the RB25 an auto and if so did you remove the auto spigot and replace with a manual spigot bearing?

Cheers

Ben

Josh_TypeX Proficient

Josh_TypeX

Posted
  • Author
Posted

OMG thank you! I don't know what I was thinking when I wired up the alternator, I had the cables in the wrong spot lol. Had been a long day. Everything works now! The noises have died down a bit now, I think I can suss out where there from.

p.s. Ben you are a legend!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • PranK
      Slight brake pedal stutter after new pads

      By PranK · Posted

      Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...