Jump to content
SAU Community

Recommended Posts

Righto

Things I have that I don't need:

RB26 twin td06 20g turbo kit

what does it include?

manifold

turbos

oil lines with dash fitting and heat coatings

dump pipes

intercooler pipes

all silicone joiners and clamps

every nut and bolt to strap this mega power kit to your car

Please note that it's priced to sell

Manifold has no cracks in it and has not be welded since Trust made it

Note this kit comes with every farking nut and bolt you need to place it on your Gtr

I would recommend a re-build for both turbos just to be on the safe side (re- builds cost from 300 from a normal turbo joint to 500 from gcg)

I would also ceramic coat the manifold and housings if you buy it

Cost is around the 650 mark from Craved

I can arrange this if you want

Turbo are on the car and I'm happy to take you for a 1.8bar trip to show you that they are the shit and go harder than a 16 year old lad with his first porno

Turbos made 526rwkw at 20psi

Price $3500

The twins:

PB210057.jpg

Front turbo

PB210058.jpg

Rear turbo

PB210060.jpg

Manifold with single 60mm Trust wastegate

PB210062.jpg

PB210065.jpg

PB210066.jpg

PB210067.jpg

Next we have a built auto R33 Gts gearbox, not sure what its rated at but runs fine behind the above turbo kit

What do you get?

R33 gearbox

Full manualised

Flex plate

3800 rpm stall converter

Oil cooler and line

Tail shaft (i dont need it)

A selection of R33 Gts gearbox controllers

B&N pro ratchet shifter installed and adjusted to the gear box

Basically every nut and bold to hammer it into your R33 and go drag racing

Bolt in and run some times!

PB210068.jpg

PB210071.jpg

Pete

Located in lower Blue Mountains Sydney

0448468884

dam slush box

Next we have a built auto R33 Gts gearbox, not sure what its rated at but runs fine behind the above turbo kit

What do you get?

R33 gearbox

Full manualised

Flex plate

3800 rpm stall converter

Oil cooler and line

Tail shaft (i dont need it)

A selection of R33 Gts gearbox controllers

B&N pro ratchet shifter installed and adjusted to the gear box

Basically every nut and bold to hammer it into your R33 and go drag racing

Bolt in and run some times!

3k for the whole lot

video didnt work farken!

anyway ill punt up some other stuff

16 inch 5 stud waanabe rims (pair) 400

rear 17 inch disco rims 300

760cc injectors 600

trust gtr intercooler 4 inches thick 500

fancey flame painted rocker covers 200 exchange for some stockers

turbo kit will be comming off this weekend

dont be scared people

someone must want a lazy 800-1000hp kit for skidz!

lol

i also priced up some rebuild action and its 350 per turbo

ultimately if knowone buys the kit then ill have them rebuilt

so lets say 4k with rebuilt turbos

:)

hammer time!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...