Jump to content
SAU Community

Rb26 Single Turbo Kit T88


Recommended Posts

i have for sale rb26 single high rise stainless turbo manifold with a 50mm wastegate and screamer pipe with a trust greddy t88-34d turbo.

this set up has made over 600hp at wheels on a small set up. has only done dyno km reason for selling not big enough for what i em doin.

pick up only or local meet up sydney.

price $3000

post-45020-1259402887_thumb.jpg

Link to comment
Share on other sites

hey mate the rear housing is a 24g which i think means 24cm housing but yer street wise it was fun on my car it had full boost bye 4000 started spooling at 3600 but just kept boosting never dropped off. the work i did to my engine was just forges and cams nothin big just had a good tune. i would consider posting at buyers cost but i would hae rathered pick up just been a heavey item and stuff. but if need be i will post. cheers

Link to comment
Share on other sites

hey mate the rear housing is a 24g which i think means 24cm housing but yer street wise it was fun on my car it had full boost bye 4000 started spooling at 3600 but just kept boosting never dropped off. the work i did to my engine was just forges and cams nothin big just had a good tune. i would consider posting at buyers cost but i would hae rathered pick up just been a heavey item and stuff. but if need be i will post. cheers

Hey buddy wat else will be required with this set up, i have a apexi power fc wit z32 afm an wat not is that still fine? an this doesn't come with a gasket set either or water oil lines does it?

Link to comment
Share on other sites

Hey buddy wat else will be required with this set up, i have a apexi power fc wit z32 afm an wat not is that still fine? an this doesn't come with a gasket set either or water oil lines does it?

it does come with oil lines as it is only oil cooled turbo. that computer should be fine but i hope u got bigger injectors and fuel pump. u will have to get the exhaust to suite andthe intercooler pipe should be a close fit to it but may need some adjustment. but sori doesnt come with gaskets as they broke when i took them off car but they can be bought very easy.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Agreed with the rest. Also at least based on my own research, there are no readily available stock or close-to-stock RB20Neo maps that you could download and use as a base were you to buy a complete standalone ECU, and the regular 20DET maps don't really work well so you'd need to take it to a tuner if you have no experience. I installed an AEM V2 on my 20Neo+T and had lots of headaches until I got it to run and idle properly but I've yet to remap it fully. You have to start building up your timing and fuel maps entirely from the ground up; even the ones for a 25 didn't work at all.
    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
×
×
  • Create New...