Jump to content
SAU Community

Recommended Posts

Hello guys,

Still wrecking white R32 GTR, have sold most bits but have still got a lot of small stuff left. Will put engine parts on the bottom of the list.

12 coil packs, 6 of them were from the white gtr, ran fine but was only running std boost. 6 are from my grey gtr, worked well but started breaking down over 20 psi. $50 for the whole lot

Steering rack with tie rod ends, $50

Clutch slave cylinder $20

Clutch master cylinder $30

Brake Booster $30

Power steering resevoir $10

AC condensor, radiator sorta thing $30

Factory rubber intercoller hoses x 3 $60

AC fan $20

Front wheel speed sensors $50

Front right hand hub with driveshaft, front left hand hub with upper and lower arms and driveshaft $100 pair

Passenger seat, just been professionally cleaned $150

LH door, white, missing the latch and central locking piece, paint bit rough but door good $100

Bare steering column $20

Taillights, no surrounds $30 pair

Drivers side headlight, has had hole cut in bottom of headlight, dont know why but it doesnt seem to affect its operation. Could plastic weld a piece in there if you wanted it to look mickey mouse, even though you cannot see it once it is mounted in car $30

Starter motor $30

Rear cradle with brakes, diff and suspension arms, missing hicas and the hicas arms $500

Front crossmember $80

Gearbox, has done 500km on a full $1500 rebuild, the transfer case had done 2000km on a full $1000 rebuild. Only used synthetic gear oil. pretty much brand new $1500

Pair of HKS 2530's, pretty much brand new,were fully rebuilt after i blew engine, cost $2500 to repair the pair of them. Once rebuilt i put them on another engine and the other engine and i couldnt get other engine to run right so i removed them again. Selling for cost of rebuild $2500

Reco head, head has the same story as the turbos, blew engine, got new head built, Has $1400 worth of stainless steel valves in it, type B cams, heavier valve springs, all reshimmed etc by engine reconditioner. Sell for $2200

Sump with diff etc, diff good but needs checking, i havent had in a car for a long time. $50

Gmax 6 spoke white wheels, 17x8 with +32 offset, no tires $400

Have got heaps of other little engine and car parts, just ask.

Thanks,

Michael

Link to comment
https://www.sau.com.au/forums/topic/298185-wrecking-and-for-sale-r32-gtr-stuff/
Share on other sites

  • 2 months later...
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...