Jump to content
SAU Community

Recommended Posts

hey guys, have a few spare parts that we need gone...

pair of r32 gtr turbo's, come with everything pictured (bar surrounding items and head)... turbo's are in average condition, some shaft play, to be expected due to their age... not sure of k's, was purchased with some other parts we needed...

$400 with the lines (as pictured) $350 without, also have a pair of O2 sensors, which we can supply for an extra $60...

R32 GTR 3" exhaust, cat back, stainless steel, in good condition, no holes etc... de-cat pipe not included... $350

r32 GTR standard front pipe, with heat sheilding etc-as pictured, in good usable condition... $60

Rb26 polished camshaft covers, highly polished, alot of money went into these, selling cheap at $650

Rb26 polished plenum, highly polished, looks great... also have ported runners internally to smooth flow... $600

located on the far north coast NSW, near lismore, can personally deliver as far up as brisbane at a cost, otherwise aus wide postage is available at buyers expense (for the smaller items). cheers

post-53835-1260696245_thumb.jpg

post-53835-1260696462_thumb.jpg

post-53835-1260696538_thumb.jpg

post-53835-1260696602_thumb.jpg

post-53835-1260696690_thumb.jpg

post-53835-1260696803_thumb.jpg

post-53835-1260696910_thumb.jpg

post-53835-1260696986_thumb.jpg

  • 2 weeks later...

common people, someone must want a decent exhaust... taking reasonable offers, and we can deliver to you if you are close... need the exhaust gone, price drop on turbos to $250 firm...

sebastion, or should i say levi/alex

As you are a business/trader you are required to pay trader fee's to advertise your goods here.

Details can be found here:

http://www.skylinesaustralia.com/forums/Bu...se-t294953.html

Premium traders are currently full.

Also, do not troll the WTB section/send PM's to people about goods, this still counts as trading.

Thanks.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...