Jump to content
SAU Community

Recommended Posts

Hi, I bought my 1997 r33 gts-25t about a week ago and it didn't have an alarm. After going around to various places to get quotes for one, when I was cleaning my car the other day I noticed a strange box underneath the dash. After googling the 4 letters that were actually in english on it I found out that it's an alarm system, however I didn't get the remote with it. I was just wondering if it's usual for importers not to give you the remote? Also is it possible for an alarm shop to install another brand remote to work with this system?

Thanks

Matt

Link to comment
https://www.sau.com.au/forums/topic/300337-r33-alarm/
Share on other sites

usally the dealer wont even see the remote to the alarm, they will just get a key to the car and thats it, wethere its from the remote being lost on transport or just not being sold with the car, as for another brand remote programed to it, it all depends on the alarm its self, maybe you should post up what letters you found on the alarm and anything else you know about the alarm system, i know chris rogers knows alot about different brands of alarms and remotes, as for me im know knowegable on alarm remotes and what alarms they will work with, just how to knstall them. one of you better options in the end might just be to have a professional install a new alarm and remove the old one.

Link to comment
https://www.sau.com.au/forums/topic/300337-r33-alarm/#findComment-4990905
Share on other sites

could well be the dealer fitted nissan/alpine thing I remove. is there a security light on the dash that is marked 'seciruty'?

easier to rip the lot and put a proper one in. (properly!)

Link to comment
https://www.sau.com.au/forums/topic/300337-r33-alarm/#findComment-4991204
Share on other sites

Thanks for the replies, I was thinking that getting a new one installed would be the best way, just thought that I might be able to save some money by just getting a remote coded to it. The current alarm is http://blog.livedoor.jp/joy_carlife/archives/64868838.html. I just used googled translator to translate it. Does anyone know approximately how much it would cost to get a mongoose M80 installed?

Link to comment
https://www.sau.com.au/forums/topic/300337-r33-alarm/#findComment-4991375
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...