Jump to content
SAU Community

Recommended Posts

Hi everyone

Have recently started hearing a strange noise from the front of my car. the best way i can think to describe it is that its kinda like running a wheel over those noise lines on the side of the highways (small bumps that make that noise to wake drivers up) BUT my car is only doing it at just above 3000rpm, about 40kmh at 25% or so throttle in 2nd and just below 3000rpm, about 60kmh at about 25% throttle in 3rd.... Not sure what it is so hoping someone here has had a similar issue. The noise only lasts about 2 seconds i guess at the most and doesnt happen if i give it full throttle or different throttle applications, seems to be limited to about 25% throttle or near enough. Lets just say light throttle anyway

also if it has anything to do with it, i can sometimes hear over bumps another noise that sounds like I've left a hose clamp loose on a pipe so its just flapping around there making a very light metal on metal noise. Its not constant, sounds just like hose clamps tapping on intercooler pipes or something over bumpy road.

Details on car:

R33 GTST 1994

FMIC

X-Force 3" turbo back exhaust

K&N pod filter in cold air box

Splitfire Coilpacks

Power FC

stock suspension

stock turbo

recently put a front strut brace on and replaced my bov with an aftermarket one (that is plumbed back)

100,000km service has been done, car has 113,000km's on it now.

The 2nd noise described has been happening for a little while now and the 1st noise i described is more recent

If anyone can help me that would be great :3some: Ive looked around and cant notice anything so im a bit stumped

Thanks

Callan

Edited by 89CAL
Link to comment
https://www.sau.com.au/forums/topic/300528-strange-noise-from-front-of-car/
Share on other sites

I get a noise like the first one you described in second gear when I am at lower revs but I think its because I have a heavy duty clutch and it needs more revs to get going. But thats at like 1200-1500rpm. Is the noise like when you put the car in a higher gear e.g. 4th and your at low speeds/revs and try to accelerate or.....? You havent had the clutch changed or anything lately have you?

Strangely enough it was my blow off valve

I think it is either the seal for the screw in outlet (Which is different as i had a plumback one made up) not sealing on the o-ring

OR I removed one of the internal springs (had 2) because i had the same bov previously and it wasnt going off so i removed one of the springs to get it to work and later found out the diaphram was broken

So anyway, it was just the BOV, as for the other noise, not sure but it cant be anything major, think its just a loose bolt or something floating around

Yeh i have an aftermarket clutch but i know th strange noises it makes lol and this was a new one

All good. Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
    • Yeah. OK. I'll say the same thing I say to everyone. You do not have to use 100% throttle all the time.
×
×
  • Create New...