Jump to content
SAU Community

So After All The Hype, Speculations Etc, Is The R35 Gtr What It's Cracked Up To Be?


Recommended Posts

None of yours, mine or anyone elses business imo.

I wasnt making it my business. I was simply stating its a huge leap. Didnt ask for a run down of his life/finances

  • Replies 126
  • Created
  • Last Reply

Top Posters In This Topic

I think it's disappointing that EVERYONE is cashing in on the R35 wave.

Tuners, dealers, body kit manufacturers, performance parts suppliers, ECU suppliers, the Government and so on.

Why is everything SO expensive related to the R35. I'll tell you why, it's called profiteering.

Cobbs access port R35 $995 - Infiniti $695

Cobbs downloadable maps - buy only

Haltech Platinum ECU R35 $4495 Any other $2195 - hey it's the same unit, only looms different !

Simple economies of scale.....

R&D, warranty...ton of factors influence the pricing of aftermarket parts. Every company that wants to develop products for the R35 needs to purchase or borrow test mules as a starting point. This kind of capital needs to be covered. Keep in mind also that if something should go wrong (warranty wise) with an R35 because of a faulty product, well it's alot more expensive to replace a VR38 than an RB25.

Buy the Ferrari and take everything that goes with it :)

That said, there are some seemingly generic items that see unnecessary overpricing IMO.

There is often NO warranty with aftermarket parts.

Tune it and it breaks..... often its your problem. No one elses.

But it is the same with all expensive cars... Lambo hi-flow cats....= big bucks.

For something that costs F-all!!!

Ok fellas, I've called around a few places and I think it's a bit of an issue getting the car complied and all the other hassles that come with it.

Financially, I am selling one of my houses so purchasing it in cash is going to be no issue. However, getting one imported is...I rang Nissan and apparently they've put a freeze on the importation of GTR's - why is this - can someone please explain?

Ok fellas, I've called around a few places and I think it's a bit of an issue getting the car complied and all the other hassles that come with it.

Financially, I am selling one of my houses so purchasing it in cash is going to be no issue. However, getting one imported is...I rang Nissan and apparently they've put a freeze on the importation of GTR's - why is this - can someone please explain?

Of course nissan is going to say that :)

Speak to Beer Baron on here (richard, top bloke and has bought in a few R35)

Oh quick point for all those talking about warranty to if you cant afford to break it dont buy, that is my motto for all cars im looking to buy.

I learnt the hard way when i was an apprentice.... Heavily modded 911 porsche import came up i bought it and could never afford to keep it on the road.

There is often NO warranty with aftermarket parts.

Tune it and it breaks..... often its your problem. No one elses.

But it is the same with all expensive cars... Lambo hi-flow cats....= big bucks.

For something that costs F-all!!!

I said because of a faulty product, i.e. manufacturing fault. Whether warranties exist or not there is still legal liability to be had by selling someone a faulty unit. Just like oil companies are responsible if equipment goes crash and it can be proven the oil was contaminated. In the end all capital is covered by end user pricing, and given there's alot of capital involved with developing for the R35...prices are going to reflext this. As someone said before, it is also a niche market for now = market skimming rather than penetration.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...