Jump to content
SAU Community

Recommended Posts

hey my next car is goin to be a skyline once ive sold my 180, ive heard some skylines with a really nice notes to there exhuasts (deep roar) etc and was wondering how to get this?. does it matter on size of exhaust? 3 inch or 3.5 inch, muffler, custom or jap brand or is it somethin else.

cheers :D

hey my next car is goin to be a skyline once ive sold my 180, ive heard some skylines with a really nice notes to there exhuasts (deep roar) etc and was wondering how to get this?. does it matter on size of exhaust? 3 inch or 3.5 inch, muffler, custom or jap brand or is it somethin else.

cheers  :D

i would stay 2.5" with the pipe. it is not necessarily only the pipe diameter that creates what it is you are looking for: it is more in how the components of the exhaust system are set up. for one, you may want to try a resonator. this is an in-line component that will keep the phatter exhaust pipe from sounding tinny. also, the choice of cat will affect the sound, as will the initial pipes leading off the engine (exhaust manifold). you can get a high-flow manifold, header, and that will dramatically change the sound quality. next is the muffler itself. the larger the bore, the deeper the sound; the smaller the bore, typically, the higher the note. there is no "right" exhaust system or "wrong" exhaust system. it depends on how much money you want to sink into it, and what is available to you. and it depends upon the number of cars you personally research and listen to. people tend to like greddy; i have magnaflow. check out random technologies cat.

i find that skylines in general with jap exhausts (3" normally)have a very distinct note to them much like a rexy. u can tell its a skyline even before u see it. i guess the quality of the note also depends on the material used and wall thickness?? my mate has a custom stainless turbo back sys on his 180 and it sounds very hollow and tingy. does ur 180 sound simliar??

mild hpc copated steel piping delivers the best sounding exhaust note, even better with an external w/g. stainless steel gives a slight drony-tinny noise and titaniun is only a louder version of s/s

i would stay 2.5" with the pipe. it is not necessarily only the pipe diameter that creates what it is you are looking for: it is more in how the components of the exhaust system are set up. for one, you may want to try a resonator. this is an in-line component that will keep the phatter exhaust pipe from sounding tinny. also, the choice of cat will affect the sound, as will the initial pipes leading off the engine (exhaust manifold). you can get a high-flow manifold, header, and that will dramatically change the sound quality. next is the muffler itself. the larger the bore, the deeper the sound; the smaller the bore, typically, the higher the note. there is no "right" exhaust system or "wrong" exhaust system. it depends on how much money you want to sink into it, and what is available to you. and it depends upon the number of cars you personally research and listen to. people tend to like greddy; i have magnaflow. check out random technologies cat.

Please pay no heed to this post.

2.5" exhaust... WTF? Maybe for a Naturally aspirated car like a Maxima, but turbocharged cars need as little backpressure as possible.

The bigger the better.

yeh i have a 3 inch exhaust from the turbo on my 180 with hi-flow cat and resonator and it sounds pretty mean, yeah bonze what the **** are you on about? are you a serious member on this board?, also would there be any difference if the external wastegate vented back into the exhaust sound any different or just vent it to atmosphere? also guys ive been a very long member on nissansilvia.com and know alot of shit about cars so ill just let you's know im not a newb to this.

cheers.

oh yeah ive seen blast (brand) mufflers on alot of skylines and they sound deep as all shit.

and can you guys check out this site and watch the short clips from uniques skyline, 1mb or less of there exhaust that sounds ****ing crazy

http://www.uniqueautosports.com.au/performance.htm

If you want a nice sounding exhaust make sure you have a muffler and a resonator. Removing the resonator will or should :D create a crackly sound. That is the basis with V8's not to sure if it applies to the Skyline but I see no reason why it shouldn't.

I've got a custom aussy built s/steel exhaust that set me back $1700. Its a 3" from the turbo, 7litre high flow 3" cat, s/steel large hot dog looking resonator in the middle and a large rear s/steel polished rear muffler with a 3" s/steel tip to keep things looking stock.

It doesn't drone in the car but is louder than most jap exhaust skylines. It has more of an Straight Aussy 6 grunty type sound. I compared it to sounding similiar when cruising along to my old 250cortina that had a set of extractors & 2.5" exhaust.

I have heard 1 R33 that sounded absolutly awesome. Not sure which exhaust he had but i'd prefer it over the sound of a V8 it was that nice.

It sounded hell grunty with a really deep loud note where you could hear alomost every cyclinder firing not the muffled deep sound. Not to loud where it was annoying though.

I have Trust MX exhaust. Nice sounding exhaust note. Deep grunt when launching then turns into a very sweet rush exhaust note... Not tinny or crackling whatsoever. Its basically come with a resonator and proper size rear muffler with a 4" tip.

The front pipe won't make it louder cos I have it on mine and doesn't make a difference. The only time where you will start to make it so loud is if you put an atmo-venting dump pipe, or in other word: screamer pipe.

Kakimoto exhausts sound very good on on a RB25 too. Not too loud either.

Today I also heard a Go-Zigen (5Zigen) exhaust system on an R33 GT-R. It also has a nice deep sound to it without being too loud too.

I think mine is also a kakimoto exhaust...turbo back system with a massive catalytic converter. It's quiet, but sounds perfect.

going into underground carparks and stuff, u can hear a very bass-y growl, shakes things around u. Turns heads n what not...I've received plenty of compliments.

It puts the turbo's sound into the limelight as well instead of drowning it out. makes a good combination sound when u're thrashing the car around. Sounds like a jet almost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
    • Had I known the diff between R32 and R33 suspension I would have R33 suspension. That ship has sailed so I'm doing my best to replicate a drop spindle without spending $4k on a Billet one.
    • OEM suspension starts to bind as soon as the car gets away from stock height. I locked in the caster and camber before cutting off the kingpin. I then let the upright down in a natural (unbound) state before re-attaching it. Now it moves freely in bump and droop relative to the new ride height. My plan is to add GKTech arms before the car is finished so I can dial camber and caster further. It will be fine. This isn't rocket science. Caster looks good, camber is good, upper arm doesn't cause crazy gain and it is now closer to the stock angle and bump steer checks out. Send it.
    • Pay careful attention to the kinematics of that upper arm. The bloody things don't work properly even on a normal stock height R32. Nissan really screwed the pooch on that one. The fixes have included changing the hole locations on the bracket to change the angle of the inner pivot (which was fairly successful but usually makes it impossible to install or remove the arm without unbolting the bracket from the tower, which sucks) and various swivelling upper arm designs. ALL the swivelling upper arm designs that look like a capital I (with serifs) suck. All of them. Some of them are in fact terribly unsafe. Even the best one of them (the old UAS design) shat itself in short order on my car. The only upper arm that works as advertised and is pretty safe is the GKTech one. But it is high maintenance on a street car. I'm guessing that a 600HP car as (stupidly, IMO) low as you are going is not going to be a regular driver. So the maintenance issues on suspension parts are probably not going to be a problem. But you really must make sure that however your fairly drastically modded suspension ends up, that the upper arms swing through an arc that wants to keep the inner and outer bolts parallel. If the outer end travels through an arc that makes that end's bolt want to skew away from parallel with the inner bolt, you will build up enormous binding and compressing forces in the bushes, chew them out and hate life. The suspension compliance can actually be dominated by the bush binding, not the spring rate! It may be the case that even something like the GKTech arm won't work if your suspension kinematics become too weird, courtesy of all the cut and shut going on. Although you at least say there's no binding now, so maybe you're OK. Seeing as you're in the build phase, you could consider using R33/4 type upper arms (either that actual arm, OEM or aftermarket) or any similar wishbone designed to suit your available space, so alleviate the silliness of the R32 design. Then you can locate your inner pivots to provide the correct kinematics (camber gain on compression, etc).
    • The frontend wouldn't go low enough because the coilover was max low and the upper control arm would collapse into itself and potentially bottom out in the strut tower. I made a brace and cut off the kingpin and then moved the upright down 1.25" and welded. i still have to finish but this gives an idea. Now I can have a normal 3.25" of shock travel and things aren't binding. I'm also dropping the lower arm and tie rod 1.25".
×
×
  • Create New...