Jump to content
SAU Community

Recommended Posts

I have for sale the following items:

1. R33 GTSt brake calipers, rotors and pads $500 (If sold seperatly $350 for the Fronts and $150 for the Rears)

2. R33/34 GTR JJR intercooler hard piping kit powdercoated black by Craved Coatings, including silicon hoses $350 (Missing hose clamps)

3. R33 car jacks $30 each

4. R33 push type slave cylinder with line $60

5. RB26 cam cover $60 (will require respray)

6. Exhaust cam bracket $20

7. Stock R33 GTSt BOV with pipe $50

8. R33 GTSt crankshaft and crankshaft girdle $100

9. RB26 badges Large $30 Small $10 each

10. RB20/RB25/RB26 Gates timing belt $80

11. Stock R33 handbrake shoes $50

12. Stock RB25 conrods $60

13. R33 GTSt thermo fan $60

14. R33 GTR front and rear rotors Make an offer

15. Various plugs for radio/headunit $10 each

16. RB26 push in cam cover fitiings -10 size $30

17. N1 oil pump gears $300

18. R33 GTSt manual, series 1 speedo cluster $60

19. Apexi power FC hand controller 415-N001 $350

I am located in Sydney, happy to post interstate at buyers expense

Edited by Smoky
Link to comment
https://www.sau.com.au/forums/topic/302659-rb25-rb26-parts/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

5. RB26 cam cover $60 (will require respray)

i'll take this if its the pair of cam covers (like the actual camshaft covers...)

16. RB26 push in cam cover fitiings -10 size $30

and if these fit the RB25 cam covers i'll take them too

Link to comment
https://www.sau.com.au/forums/topic/302659-rb25-rb26-parts/#findComment-5018200
Share on other sites

5. RB26 cam cover $60 (will require respray)

i'll take this if its the pair of cam covers (like the actual camshaft covers...)

16. RB26 push in cam cover fitiings -10 size $30

and if these fit the RB25 cam covers i'll take them too

Sorry, I should have put it as RB26 timing belt cover, no cam covers for sale

To my knowledge they will only fit an RB26

Hi mate, interested in the Apexi Power FC, i still have the stock ecu, is this a plug in piggy back system? or does it replace the whole ecu? thanks, i live in perth btw. oh and it works good?

No Power FC for sale here, just the Hand Controller

Link to comment
https://www.sau.com.au/forums/topic/302659-rb25-rb26-parts/#findComment-5018283
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...