Jump to content
SAU Community

Summernats

Donnan

By Donnan,
in Australian Capital Territory

 Share

Recommended Posts

nerm Mentor

nerm

Posted
Posted (edited)

apparently last night as soon as it hit 10 the police shut down the area and started defecting everyone, a guy at work only just got away without a defect by legging it (his car is about 4-5cm of the ground.. literally).

if your going to bring your car dont park anywhere near lonsdale street (or whatever that main street is called) or leave before 10pm

personally im going to go stealth in the 'rago.. anyone want a lift :)

Edited by nerm
Link to comment
https://www.sau.com.au/forums/topic/302747-summernats/#findComment-5022226
Share on other sites
Bluprint Veteran

Bluprint

Posted
Posted
apparently last night as soon as it hit 10 the police shut down the area and started defecting everyone, a guy at work only just got away without a defect by legging it (his car is about 4-5cm of the ground.. literally).

Really?

Frink and I got in there at about 9:45, we drove my car in there and parked right in the middle next to the Lonsdale St. car wash and sat there until 10:30 and saw a fair few cars, but not heaps. Cops stopped a few people but we didn't see any big shutdown at 10pm, nor mass defects.

Link to comment
https://www.sau.com.au/forums/topic/302747-summernats/#findComment-5023686
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      RB26 swapped gtst

      By GTSBoy · Posted

      Just get rid of the orignal low impedance injectors, replace with modern high impedance injectors, and you won't need the resistors. Wire direct, as per any other engine.
    • GTSBoy
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By GTSBoy · Posted

      Tao, we're not talking about the ECU boost ref. We're talking about the wastegate signal source.
    • GTSBoy
      Belt flex under throttle

      By GTSBoy · Posted

      Flapping up and down is a consequence of the varying pull on the belt. When the engine speed is suddenly increased, the tension in the belt increases too. When that engine accel changes to decel, the tension is reduced and turns up as a little extra length of beltes between the pulling and dragging pulleys. That extra length flaps up, then down. There's all sorts of other harmonic stuff going on too.
    • r33.antwone
      RB26 swapped gtst

      By r33.antwone · Posted

      hello ladies and gentlemen so i’ve swapped a rb26dett into my r33 gtst and ive come across many speed bumps but its nearly over what im having issues with is the injector resistor box that are normally on the RB26 fuse box but im still using my rb25 fuse box and as a result my injectors aren’t getting power and is the last thing i need to figure out so the car can start. can anyone help me out on where i can find a wiring diagram for the rb26 harness to see where the injectors are supposed to receive power 
    • hypergear
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By hypergear · Posted

      The boost pressure at the compressor cover will be higher than at inlet manifold. lets say, trying to hold 20 psi flat at 7000 RPM. If your wastegate opens at 20 psi measured at the compressor cover, the engine may only be seeing 16 psi. Your base pressure reading at engine would be 20psi by 4K and 16psi by 7K while your MAP at compressor housing still reads 20psi at 7K. For this reason your ECU's MAP source is never on the compressor cover. This difference isn't a major concern if you're using an electronic boost controller (EBC).
×
×
  • Create New...