Jump to content
SAU Community

Recommended Posts

Sorry to put this in here but not many ACT people seem look at the F/S section.

I'm selling two wheels, not sure what they are but look like Advan AVS VS-5?. Condition isn't great with a few scratches and what appears to be paint peeling in the centre on one of them. I used these as wheels for drift but now I'm trying to save some money. I bought these off Cejay originally so he might be able to shed some light on them.

They are 17", I think either 8" or 8.5" wide. One has a Yokohama Ecos and the other some sort of Falken, don't think either would be legal but would have enough meat for a fair few laps out on a drift day, they are 235/45/17's.

Lookin for $150ish for these, or make an offer.

Please PM me or contact me on 0430 508 321.

Cheers,

Adrian

post-1667-1262769983_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/302766-2-x-17-wheels/
Share on other sites

Pretty sure at least one of the pairs was 8 inches wide with an offset of 32. If you have no takers I may be interested in buying these rims back. The front set needed spacers I think to clear the calipers. These came on the car. And were painted that stupid orange by the yard I bought the car off. They did a shit job, and it's only the front of the wheel that has been powdercoated.

Link to comment
https://www.sau.com.au/forums/topic/302766-2-x-17-wheels/#findComment-5021291
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...