Jump to content
SAU Community

Extremely Bad Missfire And Rough Idle


Chris34
 Share

Recommended Posts

Ok so firstly, the problem. Soon as I start the car, it idles fairly smoothly as per normal however you can feel these low-pitched subtle pops/thumps coming out of the exhaust which you can feel while sitting in the car. As I start driving it, the car starts jumping and that low-pitch popping sound becomes consistent with the revs and basically the car barely goes anywhere. I first had it looked at through a workshop and he said it was probably burnt out spark plugs, turns out yes my spark plugs were burnt out so brand new ones were put in.

I picked up the car and the car drove perfect! That was until boost comes in, as soon as boost came in, the same thing happened again (as above). Then for a short period of time on the way home, it was all clear and the car drove perfectly both on and off boost and was as it use to be. But then the problem came back where the missfire and popping/thumping would happen just above 1500rpm. I barely made it home.

Does ANYONE know what the problem is/what's causing it?

Not sure if it's relevant or not, however last week the car overheated due to the plastic spout on top of the stock radiator breaking. I had a new Koyo Aluminium Radiator installed and when I picked it up from that workshop that installed the radiator, that's when this problem occured. However they stated they touched nothing but take out the old radiator and drop in the new one.

Link to comment
Share on other sites

If your plugs were that old, and it depends how many km's your OEM coil packs have done, I would suggest if you can afford it to replace all 6 x Coil Packs to compliment your new plugs with after market ones (Splitfire, Superspark etc) to save yourself any headaches in the long run. Superspark's are an excellent choice for the price range.

Link to comment
Share on other sites

Ok so firstly, the problem. Soon as I start the car, it idles fairly smoothly as per normal however you can feel these low-pitched subtle pops/thumps coming out of the exhaust which you can feel while sitting in the car. As I start driving it, the car starts jumping and that low-pitch popping sound becomes consistent with the revs and basically the car barely goes anywhere. I first had it looked at through a workshop and he said it was probably burnt out spark plugs, turns out yes my spark plugs were burnt out so brand new ones were put in.

I picked up the car and the car drove perfect! That was until boost comes in, as soon as boost came in, the same thing happened again (as above). Then for a short period of time on the way home, it was all clear and the car drove perfectly both on and off boost and was as it use to be. But then the problem came back where the missfire and popping/thumping would happen just above 1500rpm. I barely made it home.

Does ANYONE know what the problem is/what's causing it?

Not sure if it's relevant or not, however last week the car overheated due to the plastic spout on top of the stock radiator breaking. I had a new Koyo Aluminium Radiator installed and when I picked it up from that workshop that installed the radiator, that's when this problem occured. However they stated they touched nothing but take out the old radiator and drop in the new one.

Hay i had a very similar problem with my R34 after checking all the above mentioned problems new plugs new coils. i pulled the cas spun the shaft and there it was noisey bearings. pulled it apart marked it carefully pressed on new bearings put it back in bang full power again. no problems even put my old coils back in perfect.

It is actually the fastest check out of all the possible problems and $15 to fix.

Link to comment
Share on other sites

I maybe over doing it here but. You say it overheated? by how much and for how long? these things have alloy heads, i.e. to hot for to long and your head starts to warp (Very bad) Has it used any coolant at all?

might be something to look into

Link to comment
Share on other sites

Found out it was the wiring loom/harness for the coilpacks. 2 of the plug clips were cracked so they were basically half in half out sometimes.

In regards to the head being warped...is this something that could be potential in the near future? What's the easiest way to tell?

Link to comment
Share on other sites

  • 1 month later...

i think i may know what it is, i got the same problem turns out to be the crank shaft sensor, get it fixed or else it could fk up the timing and bend your valves

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • I’m sure this has been discussed many times. But anyone have any or know someone that is selling genuine N1 rear pods? I’m still shocked no one replicates these yet. Looking to buy some. Added a photo of the part. 👍🏻
    • Hello, The dog bone wont have much to do with this - the calliper applies a load about the disc - the outside of the calliper is more flexible than the inside by virtue of it not haveing the big torqued down bolts, additional metal structure on the caliper itself, and mostly not being cantilevered. So the outside of the calliper is pushing away as its more bendy and brining the inside with it as an equal pressure on both sides of the caliper looks to cause more flex on the outside - which makes sense. I have done this same thing with the calliper unbolted from the dog bone - same thing happens. Although id have to watch more carefully to see how much more the outside moves than the inside in this case. Im guessing there is a point in the pedals travel where the pressure is not actually increasing in the system - its just volumne displacemnt - and because the outside of the calliper is more flexy, it receives that volume. Have gone back to Alcon again - but beyond a resolution there I would stay clear of this calliper and possibly any of the lighweight type of callipers - especially if you have the smaller 15/16" master cylinder. Cheers.
    • Yes, you can very clearly see from more than one angle that it is the whole caliper moving left-right, not deformation of the caliper. The top moves, the bottom moves. Equally. It should be possible to see where the movement is occurring. Just need to look more closely.
    • Hi Folks, my 2009 Skyline 370GT “Crossover” wagon is losing water and has been diagnosed as needing a water pump replacement (it’s an internal timing-chain driven unit, not the usual electric type that seems to be used across many manufacturers). Am looking for any repairer recommendations in the Sydney /Wollongong region who can be trusted and are experienced in this sort of work on the VQ 36 engine. Many thanks….Bill
    • While all of the above makes sense, we're not talking about some Ling Long calipers of AliExpress; Alcon would have to be one of the top 5 caliper suppliers in the world and these are not their budget units. If there were manufacturing defects in the caliper causing this issue I'd be very disappointed. Having re-watched the video a few times I think it's dog bone/mount related. The caliper moves independently to the rest of the suspension and brake assembly which suggests to me that it's not mounted rigidly. I know this sounds stupid, but have you got enough thread on the retaining bolts or are they a poofteenth too long and it's not super tight? For axial movement to be occurring without deforming the caliper that can be the only answer.
×
×
  • Create New...