Jump to content
SAU Community

Rims For Sale: Project D D1 18x10 Lenso Monoblock Light Race Spec Rims

cardre
 Share

Recommended Posts

cardre Enthusiast

cardre

Posted
Posted

Hi,

Got the following rims only (NO tyres) for sale.

Project D D1 18x10J Lenso Monoblock Light Racespec rims (NO tyres)

GTR offset +22, to sit centred. Will suit other cars as well.

Bought them brand new and used for two track days only. No marks, scratches, etc. excellent condition.

2 of the rims have lost a sticker each, but that was to be expected.

Asking $950 ono + s/h or (prefer) p/up

Located in S.A. Mb 0417 418 852

post-69474-1263374654_thumb.jpg

post-69474-1263374719_thumb.jpg

post-69474-1263374809_thumb.jpg

cardre Enthusiast

cardre

Posted
  • Author
Posted

Sorry about this skynet, but unfortunately I'm new here and I can't reply to a PM yet.

The offset I deliberately bought them for was to sit as perfectly centred as possible on a R33 GTR. That way I could get the largest rubber on them without touching the guards. I had 265x35 tyres on them and they didn't touch. So I'd say depending on what width tyres you put on them, they should be fine with your car as well.

cardre Enthusiast

cardre

Posted
  • Author
Posted
do you accept swap with my work cr kai emotion 18x9.5 offset 20?

Sorry, no.

Through doing brake upgrades, I've got 3 different sets of rims and tyres I need to sell. These Lenso in this thread, ROH Drift R in another as well as some original R33 GTR 17" rims and tyres. So I'm not after any more!

Thanks.

cardre Enthusiast

cardre

Posted
  • Author
Posted
Could you weigh the rims? I'm interested to see how much these weigh.

thanks

Sorry, they're at the workshop, so I don't know off hand.

According to this thread though, it looks like they're around 12kg each, but I'm not 100% sure.

SAU forum entry

cardre Enthusiast

cardre

Posted
  • Author
Posted
Hi mate would these fit a stock r34 gtt?

I'd reckon they would. As they're 18x10, you'd just need to be careful how wide the rubber is you put on them. A 265 tyre sat straight on them, so you could go thinner or wider depending on what you're looking for.

  • 2 weeks later...
  • 5 years later...
niZmO_Man Grand Master

niZmO_Man

Posted
Posted

Hi pal. I have a set of these on my 32 gtr and they stick out the guard. What options do i have?

18x10 +22?

Add adjustable upper control arms (both front and rear) and wind some negative camber in. Should need about -1.5°.

Unless your guards aren't GT-R...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...