Jump to content
SAU Community

Light Throttle Issues.

Shaun O

By Shaun O,
in Engines & Forced Induction

 Share

Recommended Posts

Shaun O Enthusiast

Shaun O

Posted
Posted

Annoying problem that's crept itself up, on very very light throttle, the engine stutters a little, like, super light throttle (1k-1.5k~ or so RPM while in neutral) - it's not the throttle cable either because it does it when you manually give it throttle off the throttle body.

Any ideas?

Giving it a tad more throttle and it's no problems. It just makes the ride really jerky sometimes when driving in like 2nd gear at low throttle. It's an RB25DET throttle body (S2)

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/304572-light-throttle-issues/
Share on other sites
Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
Sounds like its running lean there, possibly due to the airflow meter being dirty. Give it a clean first with a can of CRC airflow meter cleaner and see if that fixes the issue first.

Cheers, I don't have any CRC AFM cleaner, will something like Isopropyl Alcohol work?

260tech Proficient

260tech

Posted
Posted

Yup, isoprophyl alc is good, absorbs water & leaves no residue, also check plugs for gaps, & coilpacks for moisture & crap that will make things (sparks) track. give the coilpaks a wash with the iso & spray with a silicon inhibitor. Quote gospel from PI #116

Cheers GW

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
are you using an aftermarket ECU?

add some more accel enrichment and see how you go

Nah, just a standard chipped ECU, it hasn't always been an issue and just seems to be intermittent, it barely did it at all on the way to work this morning. I'm still at work though so haven't tried the cleaning stuff yet.

FULL RABBIT OR NO RABBIT!!!!!! noone likes a tortoise, light throttle is for wimps.

Haha, unfortunately that doesn't work so well in peak traffic :(

Plus, I wish my car had a lawnmower style throttle instead of an accelerator pedal :P:D

NZM.031 Grand Master

NZM.031

Posted
Posted

ok so you want it fixed then.

afm or sticky butterfly would be a good place to start... get out with some carby cleaner.

slight vacuum leak.

dodgy injector, may be spraying to much or dribbling out and flooding one cylinder or not spraying enough due to blockage and running lean in one cylinder.

dodgy plug, same as dodgy injector but different.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted

Well I just sprayed the AFM and all the coilpacks with iso alc - left it for a bit to dry then fired her up, it was doing the up n down up n down up n down revs at low throttle still but only for like 10 secs, from then on it seemed all good.

I didn't have any long sockets for the spark plugs but will find some if it happens again over the next few days.

Cheers guys.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted

Changed the spark plugs, no difference - thought I wanted to change them anyway :) (and only $20NZD for the set, can't go wrong)

Until on my way home, hit a little boost and FSHHHHH, the silicone joiner between the turbo and the intercooler piping blows off.

I have a feeling this has been the problem all along, leaking out of top of this joiner.

Gotta try my best to get it on real good tomorrow morning, will post back results.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
good work man... that will do it. hope its all good.

Yeah cheers, I tried my best but I think my hose clamps are being shit as well as the 90 degree silicone bend.

Getting a 90 degree stainless welded onto the end of the intercooler piping to eliminate the 90 degree silicone bend and put a straight silicone joiner between the turbo and IC piping instead.

Actually works out to be similar price in the end anyway, just a little more hassle but becomes better off in the long run.

Going to get a new hose clamp as well to replace the one that I think is no good.

Will post back results tomorrow night ;)

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted

Just f**ked around with hose clamps and shit just to see if I can have it running a bit nicer for tomorrows driving.

Started the car up, idling like f**kin' shit, hunting up and down, getting worse and worse and then stalling.

'f**k this' I think to myself, get in the car and just go for a wicked thrash.

Park back up again, idling like a f**kin' dream and not being gay on low throttle, WTF!

So see what happens tomorrow morning on the way to work! - Still going to replace the silicone 90 degree with stainless steel though.

Shaun O Enthusiast

Shaun O

Posted
  • Author
Posted
What AFM are you running? It might have the dreaded bad solder joints on the board inside.

It's an RB25DET S2 AFM, I have a 300ZX AFM here ready to go in whenever I can get the car tuned/chipped.

Is it something that I can fix myself? Or if I open it up will it be easily spotted?

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      ATCC Amaroo Park 1987

      By Ozdavroz · Posted

      Yep that's pretty much what I want to see. Racecars that look and sound like the Group A but with newer tech underneath to make them faster and safer. I'm sure there's enough VK-to-VN commodore, E30 BMWs and Foxbody mustangs shells around to make up a decent number of cars with hopefully a couple of sierras, rx7 and R31s in there too. 
    • robbo_rb180
      WTB RB25 Gearbox NSW / central west

      By robbo_rb180 · Posted

      Contact Jessestreeter.com/Skevas Racing/JustJap for a new r34 rb gearbox or go a cd00# conversion. No point playing with unknown condition gearboxes.
    • robbo_rb180
      ATCC Amaroo Park 1987

      By robbo_rb180 · Posted

      Such a shame places like Amaroo Park have been redeveloped, smaller tracks always make for good racing. Cheers for sharing @PranK there's some good Lakeside video's too. Its so hard with older the cars as parts are so rare and everything was made for a particular chassis at that point in time. Even the V8 Supercar Blueprint era cars are all different between each chassis within a team as they learnt things and made improvements. The COTF cars between each Chassis builder is different too especially motor/oil systems/intakes. The Group A stuff is worth so much too especially chassis with good history. The only way to do it would be composite panels and similar engine drivelines to the original cars. Ford sierra running Focus RS driveline, Commodore running a short stroke LS/LT or a Falcon with coyote and a H Pattern dog box. Could use a standard ecu across all models with a Torque Map and DBW for parity which is not even used in Supercars currently. Hell a TCM is almost a full chassis car these days and the suspension is not even close to standard style in the front running cars.  
    • Commsman
      spot the stagea

      By Commsman · Posted

      Dashcams Australia (13/05/25) captured JDMHSE (Vic plate) being a right tosser. 
    • Ozdavroz
      ATCC Amaroo Park 1987

      By Ozdavroz · Posted

      Wish someone would start a racing series for Group A replica cars, a bit like Touring Car Masters but for 1985 onwards and not grandpa's falcon and/or Monaro. I know they race in some historic class but that's for original cars, no replicas allowed.
×
×
  • Create New...