Jump to content
SAU Community

Recommended Posts

Hello to everyone on Skylines Australia!

I/My friend will be needing you guys now as my friend just purchased a R33 last night!

The car is in very good mint condision, Manual, only 130,000kms, so many reciepts its not even funny, car is running 200rwKw at the moment at 7psi.

We bought the car and boosted for about 50Kms arround town.

We came on boost and held it all the way to about 6,000 rpm.

After a while we start to smell Clutch (you know..), and 30 minutes after the car isnt moving anymore, or i should say very very slowly due to the clutch slipping.

So I guess the Clutch is gone? What do we have to do te get it fixed? How much will it cost? and I guess this time we want a GOOD clutch.

The only explanation to me is when the car was producing its peak power arround 6,000rpm the clutch could not handle that amout of power, and burt.. You think?

Ill post pictures up soon!

Thanks for the help Guys!!

Mati

You are probably looking at about 400 in labour from a workshop + the cost of a replacement clutch.

if it is still running the standard turbo you will be fine to replace it with a heavy duty organic one or if you just want to make it more of a pain to drive in traffic you can get a button clutch instead.

Clutches generally go under heavy load... at 6000rpm in the right gear, there isnt actually much load on the clutch.

Go out on the highway, and stomp on it in a taller gear, and that will generally apply alot more load causing the clutch to slip.

In your case the clutch does sound fried tho, but its a very quick death. Are you sure you didnt try to do a line locky and smoke the clutch instead of the tires

All we did was just drive the car normaly, no drifting, no burnouts.

All we did is just Boost, in all gears we gave it some nice boost and had fun.

Clutch was always fully out, and wwe reved to about 6-7000..

So why did the clutch decide to die?

At the start when we smelled clutch we reved to 6000rpm and then it went way to quickly to 7000.

So now the clutch is dead.

If we get a button clutch whats the difference?

We want a GOOD clutch. and where can we buy it?

Ok thanks for that guys.

So what is a good clutch I should get? Something that will last... you know.

And is there any chance i could do the install at home, or should i leave it to the garage?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...