Jump to content
SAU Community

Recommended Posts

hey guys where can i get a Nismo thermostat from? any traders on the site here selling them? (cheapest?) lol.. i tried a search!

on the track yesterday temps were getting hot when thrashing, iv never changed the thermostat yet so ill grab one of them +'s a 52mm alloy radiator and oil cooler this week =)

Thanks guys!

http://cgi.ebay.com/ebaymotors/THERMOSTAT-...sQ5fAccessories

this one is for RB20 - RB25 - RB26

BUT - This one is just for RB26

http://cgi.ebay.com/ebaymotors/THERMOSTAT-...sQ5fAccessories

what makes this so different that it will not fit?

You'll probably find once you upgrade the radiator you won't need a upgraded thermo.

Track GTR's here in melb, 380rwkw, none use anything other than factory - but good radiators. Temp's OK on hot days.

Perhaps just hold off until you put the radiator in and see if you're all good. Having it open sooner i'm not sure will stop overheating...

thats prob the best idea..

i think i want to change the thermostat for peace of mind just so i know its been done. after reading a few post looks like the standard Genuine nissan thermostat is the way to go maybe with the bleeder clip chopped off lol..

Your call but I'd leave the NEW OE thermostat as is because that jiggler valve is really only there to bleed the air out of a cold system after its been drained and refilled . If its open all the time you may get a slow warm up and cool temps in cold conditions . The std thermostat should be ~ 76 degrees which is cool compared to some things these days .

I agree that a better radiator is the smart first try . My reasoning is that if the radiator can't cope then having a cooler thermostat - or none at all won't stop it overheating . The golden rule is that the radiator has to be able to cool the water to at or below what you want the engine to run at temp wise .

I think an oil cooler is a must for track use but good radiator first .

My 2c spent , cheers A .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...