Jump to content
SAU Community

Recommended Posts

Basically searching for after market injectors for RB25 NEO is proving difficult, and the results I do find are expensive.

I've heard that injectors to suit WRX STI will also suit RB25 NEO, and they're not difficult to find at all and are also cheaper (from what I've found)

So want to clarify that they will indeed fit before I go ahead and purchase anything.

What's your reason for bigger injectors?

I also have heard that STI injectors appeared to be a fit, as they physically look the same, you have to get more details on the injectors like the impedeance. XR6 injectors are also supposed to he a fit, the only problem being the length of the injector, as spacers are needed to adapt to the neo fuel rail.

Have you looked into the seimens injecotr that are going around, you can get them with an electrical plug kit and a spacer kit so all you have to do it fit the injectors and change the plugs. These are cheap as well, I've seen them from between $500-$600 for the kits.

I'm running a set of 600cc deatchwerks injectors, they are a different shaped body to the stock injectors but a direct fit, electrical plugs are the same too. They are an American company but the service is excellant, I got mine for $600 delivered (the exchange rate was really good when I got them).

Deatschwerks are a good company to deal with. Was there an issue with the injectors sealing properly with the different body size?

If they go straight in that is another good option since fiddling around with plugs and spacers will usually cost you in labour negating any savings.

I had no issue with them sealing properly, even though they where a slightly different shape body, they where no wider than the stock ones, and the inlet and nozzel seals was the same size as the stock ones, it was a very straight forward swap. one thing I just remembered was they where slightly longer, about 2.5mm, so I had to space the fuel rail off with a couple of washers at the two mounting points. No big deal though.

Yes, I got a flow test sheet of all the injectors, both at a controled injection and static injection. I can't remember off the top of my head but they where matched to each other with a very low variance, I'll check when I get home if anyone is interested. And as you said, came with new o rings and little tube of o-ring lube to use when installing.

"XR6 injectors are also supposed to he a fit".

Referring to Josh's comment, I've used xr6 injectors on an rb30, cant comment on rb25.

But Nissan being Nissan, things will be similar/same.

My mate had to trim a bit of plastic of the top of the injector where the fuel rail pushes on but all was good.

I think upgrading to larger injectors is due to the fact alot of people want to eventully pull more power out the car, thus needing larger coilpacks or chancing your odds with the stock ones.

Anyone thought about just getting the stock injectors redrilled?, Thats what i am

going to do when i get a stagea , pretty common these days

cheers

darren

re-drilled?!? :D lol i hope you mean hi-flowed, which is also an ok option, but at around $100-$150 per injector, it comes to around the same price if not more than a brand new set of something like the Siemens DEKA ones or even Deatschwerks (depending on exchange rate).

a couple of the downsides IMO to hi-flowing are:

- even though its only when you get them, your car is off the road while they are off getting hi-flowed. for people that rely on there stagea as a daily, this is no good.

- unless the hi-flowing process involves replacing the solenoid/actuator, you still have a ~10 year old injector.

Edited by QWK32

Great feedback people. Thanks.

At this point thinking Deatschwerks... But I'll continue looking.

P.S. Yes, I'm looking at larger injectors to pull bigger figures. Next performance upgrade will be turbo and injectors.

im at 85-86% on the stock injectors running only about 10psi

looks like they are smaller than det injectors maybe, thoughts?

85% at peak flow on stock ecu and 10psi sounds right. Keep in mind that once on boost the stock tune heads fast for 10:1 AFR's, get a tunable ecu or piggy back, take some fuel out, and you'll see that duty cycle drop.

85% at peak flow on stock ecu and 10psi sounds right. Keep in mind that once on boost the stock tune heads fast for 10:1 AFR's, get a tunable ecu or piggy back, take some fuel out, and you'll see that duty cycle drop.

10-4 good buddy, nisstune or bikirom maybe will be coming, just need more moneys :D

10-4 good buddy, nisstune or bikirom maybe will be coming, just need more moneys :blush:

R34 GTT Apexi PowerFC especially if RS4S!!! less tuning time and easy fit with secret squirrel!

Anyone want these Blitz neo 525cc $600ono

post-58828-1264078463_thumb.jpg

R34 GTT Apexi PowerFC especially if RS4S!!! less tuning time and easy fit with secret squirrel!

Anyone want these Blitz neo 525cc $600ono

post-58828-1264078463_thumb.jpg

meh, $1500 for power fc + tuning or ~$1500 for a tuned biki/nisstune

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...