Jump to content
SAU Community

Recommended Posts

Hey peeps the other day i had a full 2.5" exhaust with a 4" cannon fitted to my na 34 anyhoos when driving at about 2000 rpm this fdup vibrating noise comes in and doesnt go till about 3000 is this normal as it rapes my ears cronically but it only seems to be on the inside of the car and it sounds normal outside also it sucks driving up hills coz i cant even hear my music or people in the car speak and it sounds madd as once u get past the noise any help or intuuition would be appreciated cheers jarrod.

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

if it was the gearbox it should've done it before the exhaust got fitted.

could possibly be that the exhaust is hitting the body though. might be worth getting under the car to see if it is sitting close to anything. or maybe have someone stand on the side of the road and go past them with it making the noise and they should be able to tell if it is exhaust noise or a rubbing noise

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5047405
Share on other sites

sounds like the typical rb NA drone that becomes very obvious with an aftermarket exhaust, mine will do it still, and ive got a 2.5 inch exhaust with a mid system 2in1 muffler/resonator plus a second resonator and a twin tip muffler

good news is that its easy cured by changing ur driving style, just drive in a gear lower then you normally would and let it rev up a bit (the idea being to keep it above that drony 2 or 2.5 - 3000 range) then get into 5th gear when your done accelerating - unless your in auto? then you might be stuck with it

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5047489
Share on other sites

theres a good write up somewhere on here about rb motors having a "raspy" metalic vibration or rattle sounding exhahust note at a certain rpm range but there nothing actually wrong, mine sounds a bit like this sometimes

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5054987
Share on other sites

I had that tinny crap sound ended up being that my stock nissan catalytic converter was stuffed and broken apart ... (catless and hollowed out cat's are bad for this resonance noise around the 3500- 3700 rpm area aswell )

So to fix that issue

My new exhaust system consists of the following on my R32 N/A RB20DE

Coby 6 into 2 into 1 with 2.5" outlet extractors

3" Catco Highflow catalytic converter

2.5" catback exhaust with single muffler and a canon muffler @ the rear ...

I had that issue really bad before I replaced my cat and found it to be blocked and a week later it broke apart into big chunks and allmost completely blocked up the exhaust flow ... so I pulled it all off and now fixed it all up and sounds really deep and has that good skyline note about it ...

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5055228
Share on other sites

twin cams make this rattle when you put a canon on it, the stock exhaust has a valve that opens and closes to stop this noise. Now you took it off and have a cannon it amplifies the rattle.

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5062113
Share on other sites

  • 4 weeks later...

I just got a 2.5" rear muffler and 3" tip. The sound is good, but the sound produced rapes my ears in my car too. It sounds fine outside though... I think it's because of the stock Nissan Catalytic Converter...

Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5118977
Share on other sites

Hi wht510,

It was just installed today... I think you're right about the rubber mounts... I think it could be the exhaust leaning into the bottom of the car causing the windows and the whole car to vibrate at certain RPM's.

Before I got this installed, I specifically asked for a nice tone but not enough to get defected. Also not vibrate the car. He suggested that a 2.5" rear muffler would do, and any sort of tip would be fine.

I will take it to another exhaust place to get it checked out tomorrow, Blitz Custom Exhaust (place I got it done) is closed tomorrow :D

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5119082
Share on other sites

I just went to Werribee Exhaust (99 Railway Ave, Werribee, VIC) and they have fixed the problem. The exhaust tip was too close to the bottom body vibrating the whole chassis. They let it down a few centimeters and it's all fixed now. The total cost to fix was $10.00. Muffler sounds nice in the car (windows up/down) and there's no more vibrations.

I hope this helps others with the same problem, especially to the OP.

Link to comment
https://www.sau.com.au/forums/topic/304891-new-exhaust/#findComment-5119479
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...