Jump to content
SAU Community

Recommended Posts

Guys,

Number 2 injector is leaking on my L24E, probably from the hose. What's the recommended fix?

A quick search of the forum suggests that RB30 hose/tail are straight swap but there seems to be some uncertainty if RB30 are the correct impedance.

Link to comment
https://www.sau.com.au/forums/topic/304928-replace-leaking-injector-on-l24e/
Share on other sites

im 100% sure they work. also the CA20 items work too.

funny cos my number 2 is pissing, but im getting the whole lot replaces with 270cc hosetails for my turbo setup

Any recommendations on where to source them? In one of the old posts there was a link to www.injectorsonline.com. They seem to sell L24E injectors for about $80 - what do you reckon? Have you heard anything about this mob?

Also, I saw in an old post you had some troubles removing the oil pressure sensor. How did you go removing it and presumably replacing it? Was it a tough job?

Number 2 injector is leaking on my L24E, probably from the hose...

According to the service manual, the hose can be cut using a soldering iron, removed and a new one pushed on. 

JH

According to the service manual, the hose can be cut using a soldering iron, removed and a new one pushed on.

JH

JH, so slice it length-ways with soldering iron to get it off. Then push new hose on and then the screwed down 'rail' keeps it all together? Have you done this?

JH, so slice it length-ways with soldering iron to get it off. Then push new hose on and then the screwed down 'rail' keeps it all together? Have you done this?

Haven't done it. Just reading from the R30 service manual. It says to wet the inside of the new hose with fuel, push hose and hose socket on by hand, no clamps necessary (page EF-56). 

JH

I've seen them cut, hose slid on, with a clamp

thought I throw this in as well, (when I was researching for my turbo build) not sure if they are %100 correct though

and the RB30 (non turbo) are to small for a L24 Turbo engine.

280ZX - 180cc

L20et - 188cc

RB30 - 200cc

RB30ET - 250cc

L28ET - 265cc Low Impedance

RB20DET - 270cc

RB25DE - 270cc

VG30et - 270-280cc (turbo ones)

280ZX Turbo 280cc (turbo ones) ??? not sure about this one.

7MGE Toyota 295cc

FJ20ET - 360-370cc

RB25DET - 370cc (sidefeed) No good

RB26DETT - 440cc Low Impedance

Nigel

post-13098-1264073256_thumb.jpg

Guys,

Number 2 injector is leaking on my L24E, probably from the hose. What's the recommended fix?

A quick search of the forum suggests that RB30 hose/tail are straight swap but there seems to be some uncertainty if RB30 are the correct impedance.

Just go and buy some fuel hose from repco/autopro/supercheap and cut the old hose off and replace it with the new hose. I have done this with all my injectors as well as adding hose clamps at the injector end. No more leaks.

Wardie

Yeah, I've done the cut-with-a-soldering-iron thing before and fitted new hoses - not too hard. You can buy an injector reco kit which comes with new line filters, seals etc.

But first, you might want to double check exactly where the leaking is coming from. I've had repeated problems with the black-phenolic-bush-adaptor-mount thingys cracking, so that fuel leaks from the lower ring seal. So in my case, replacing the hoses it made no difference because they weren't the course of my problems. I have a hunch that the busted adaptors might be caused by ethanol (or some other additive) in the fuel making the seal swell and crack the phenolic.

Yeah, I've done the cut-with-a-soldering-iron thing before and fitted new hoses - not too hard. You can buy an injector reco kit which comes with new line filters, seals etc.

But first, you might want to double check exactly where the leaking is coming from. I've had repeated problems with the black-phenolic-bush-adaptor-mount thingys cracking, so that fuel leaks from the lower ring seal. So in my case, replacing the hoses it made no difference because they weren't the course of my problems. I have a hunch that the busted adaptors might be caused by ethanol (or some other additive) in the fuel making the seal swell and crack the phenolic.

best way to check if injectors are leaking is by spraying it to see if it makes a change in idle... do not over tighten your injectors as the spacing blocks will crack and are quite difficult to find

on my turbo setup im useing R31 injector holders, 10 times better design, alot stronger too.

I'm still using the MR30 injector holders on my turbo L24, MAG86, do you have some picture you can put somewhere to show me what these look like and how they fit ?

Nigel

Ha ha, easy fix. Just tightened the hose clamp at the top of the hose where it meets the rail. :)

Previous own said he'd replaced inj's 1 and 2. I guess he didn't tighten up the clamps properly.

MAG86, still interested in the R31 replacment though - just for reference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...