Jump to content
SAU Community

Ultimate Budget Slap Together Rb2630det

Cartman

By Cartman,
in Engines & Forced Induction

 Share

Recommended Posts

Cartman Rising Star

Cartman

Posted
Posted

hey all just got a couple of quick questions as i'm slapping together a rb2630 out of parts i have laying around... 

the plan is to slap one of my 26 heads i have laying around onto a good condition standard rb30e bottomend i have aquired.. i have everything laying around for this except for the timing belt kit and my head bolt/stud issue.. 

my main question is about the head bolts/studs considering the 26 runs a larger size... 

Will there be any problems with me just using arp rb25 head studs? with out getting anything else even tho sleeves to sit in the 26 headbolt holes to comensate for the narrower head stud would be ideall... but this is a very very budget slap together out of parts i have laying around unless there is somewhere i can buy those sleeves providing they arent to costly... 

OR would i be better to take the complete short block into the machine shop and see if they'll drill and tap it with out pulling it apart (i dont think they'll like that idea :) )

Thanks in advance

Wazz

Cartman Rising Star

Cartman

Posted
  • Author
Posted
You can use rb25 studs as some guys here have, no modifications to the rb30 holes

Sure you dont want to freshen up the bottom end b4 u slap it together?

nah.. no need to freshen it up.. this is just a slap together out of boredem, motor was in good working order with good compression before it was pulled out... only reason it came out was for a 2530det to go in

spoke to the machine shop today and they've said just use 25 studs aswell as the head is doweled so there shouldnt be any problems with slop in the head

The Mafia Grand Master

The Mafia

Posted
Posted

Just do what I did and order a set of Durapro Bolts. Cost me $50. Nissan quoted $180 for a set of standards..

The Durapro and Nissan bolts are the exact same torque settings. The engine builder said they may even be the same bolts.

Cartman Rising Star

Cartman

Posted
  • Author
Posted
Just do what I did and order a set of Durapro Bolts. Cost me $50. Nissan quoted $180 for a set of standards..

The Durapro and Nissan bolts are the exact same torque settings. The engine builder said they may even be the same bolts.

nah, goin studs. 

STATUS Grand Master

STATUS

Posted
Posted

use new studs, i can tell you now reused ones fail. We tuned a 250000km $150 wrecker NA rb30e (still single cam) @ 22psi (300rwkw) and the brand new gasket failed due to poor clamp pressure (pushed into coolant channel) fitted new studs and it has run like a charm.

Duncan Grand Master

Duncan

Posted
Posted
spoke to the machine shop today and they've said just use 25 studs aswell as the head is doweled so there shouldnt be any problems with slop in the head

good call.

bolts job is to clamp, dowel's job is to locate. should be fine

Cartman Rising Star

Cartman

Posted
  • Author
Posted
use new studs, i can tell you now reused ones fail. We tuned a 250000km $150 wrecker NA rb30e @ 22psi (300rwkw) and the brand new gasket failed due to poor clamp pressure (pushed into coolant channel) fitted new studs and it has run like a charm.

nice work trent :) thats goin to be about what i'm aiming for out of my 275000km running fine rb30e, 10cm t67-25g should be lots of fun on it :banana: 

Cartman Rising Star

Cartman

Posted
  • Author
Posted
good call.

bolts job is to clamp, dowel's job is to locate. should be fine

they put it almost identically to how you've worded it there, i have a feeling this budget slap together is goin to make for some good fun :) 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...