Jump to content
SAU Community

Recommended Posts

hey all just got a couple of quick questions as i'm slapping together a rb2630 out of parts i have laying around... 

the plan is to slap one of my 26 heads i have laying around onto a good condition standard rb30e bottomend i have aquired.. i have everything laying around for this except for the timing belt kit and my head bolt/stud issue.. 

my main question is about the head bolts/studs considering the 26 runs a larger size... 

Will there be any problems with me just using arp rb25 head studs? with out getting anything else even tho sleeves to sit in the 26 headbolt holes to comensate for the narrower head stud would be ideall... but this is a very very budget slap together out of parts i have laying around unless there is somewhere i can buy those sleeves providing they arent to costly... 

OR would i be better to take the complete short block into the machine shop and see if they'll drill and tap it with out pulling it apart (i dont think they'll like that idea :) )

Thanks in advance

Wazz

You can use rb25 studs as some guys here have, no modifications to the rb30 holes

Sure you dont want to freshen up the bottom end b4 u slap it together?

nah.. no need to freshen it up.. this is just a slap together out of boredem, motor was in good working order with good compression before it was pulled out... only reason it came out was for a 2530det to go in

spoke to the machine shop today and they've said just use 25 studs aswell as the head is doweled so there shouldnt be any problems with slop in the head

Just do what I did and order a set of Durapro Bolts. Cost me $50. Nissan quoted $180 for a set of standards..

The Durapro and Nissan bolts are the exact same torque settings. The engine builder said they may even be the same bolts.

Just do what I did and order a set of Durapro Bolts. Cost me $50. Nissan quoted $180 for a set of standards..

The Durapro and Nissan bolts are the exact same torque settings. The engine builder said they may even be the same bolts.

nah, goin studs. 

use new studs, i can tell you now reused ones fail. We tuned a 250000km $150 wrecker NA rb30e (still single cam) @ 22psi (300rwkw) and the brand new gasket failed due to poor clamp pressure (pushed into coolant channel) fitted new studs and it has run like a charm.

spoke to the machine shop today and they've said just use 25 studs aswell as the head is doweled so there shouldnt be any problems with slop in the head

good call.

bolts job is to clamp, dowel's job is to locate. should be fine

use new studs, i can tell you now reused ones fail. We tuned a 250000km $150 wrecker NA rb30e @ 22psi (300rwkw) and the brand new gasket failed due to poor clamp pressure (pushed into coolant channel) fitted new studs and it has run like a charm.

nice work trent :) thats goin to be about what i'm aiming for out of my 275000km running fine rb30e, 10cm t67-25g should be lots of fun on it :banana: 

good call.

bolts job is to clamp, dowel's job is to locate. should be fine

they put it almost identically to how you've worded it there, i have a feeling this budget slap together is goin to make for some good fun :) 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...