Jump to content
SAU Community

Recommended Posts

Okay like most I have armorall lying around from gifts etc

Use it to detail the tyres mostly

My doorhandles and glovebox handle thingo are nearly white

Most people say armorall is the devils work etc.

My older revhed mates all say hit the handles repeatedly with the armorall

will eventually make em look the correct color

what is everyone using my handles look bad

rest of the interior is pretty resonable

other than the remnants on my dash of the black silicon previous owner used to attach the boost gauge

that will be the next mission I guess

Any suggestions????????????????

Link to comment
https://www.sau.com.au/forums/topic/305720-armorall/
Share on other sites

I accidentally got a couple of drops of the stuff on my new leather gear boot. instantly took the color out of it. Now on the blue leather there is a couple of white spots that I'm stuck with. Not looking forward to the comments that passengers may come up with ;)

I wont be using it again. Slightly Damp cloth FTW

Link to comment
https://www.sau.com.au/forums/topic/305720-armorall/#findComment-5058623
Share on other sites

Armor all is evil

It's basically a mix of solvent and sealer. The solvent gets in and attacks the plastic (vinyl / whatever) and the sealer seals it in to let it keep attacking.

You be the judge.

And it costs about 25c a bottle to make.

Link to comment
https://www.sau.com.au/forums/topic/305720-armorall/#findComment-5075144
Share on other sites

I detail cars for a living and have found anything Maguiars is the shit! Not only do they work well but all their products smell good too, doesnt smell like chemicals. Amour all is absolute crap and will cause damage eventually.

If the plastic wont go back to its original colour try a bee's wax, that fixes most things! If that fails you may have to replace the parts effected.

Hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/305720-armorall/#findComment-5075956
Share on other sites

I use Mothers Naturally Black, you can buy from any auto shop.

Pour onto the plastic, let it sit on it for a couple of minutes, then massage it into the plastic. Then buff it after it has dried. Its a longer process than all the typical black restorations, but this is different as it isnt just some black liquid to hide the faded plastic.

Link to comment
https://www.sau.com.au/forums/topic/305720-armorall/#findComment-5076008
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...