Jump to content
SAU Community

Recommended Posts

  • Replies 193
  • Created
  • Last Reply

Top Posters In This Topic

Elf LMS is the control fuel Elf originally designed and made for Le Mans, it seems like a good brew. Makes good power, consistent, excellent quality and runs cooler which is all very logical stuff for turbo engines running in a 24 hour race.

Makes only a little less power than Turbomax, and is cheaper and not as nasty to use.

Originally posted by benm

I still find it quite weird how this topic hasn't appeared long ago if its deffinetly a seat of the pants power increase. What happens in 10,000km when someone has to do a rebuild because it doesn't work out like everyone states.

This stuff has been in use as a performance increase for years.

You used to be able to buy toluene from the pump, as my boss used to run 20% in his Mini Cooper S all the time.

As for adverse engine effects, if you use 20% or under, you should be fine without engine modifications.

Hot 4s did an article on this (probably about 10 years ago now) and recommended no higher than 20% without doing other stuff to your car.

As it burns hotter than normal fuel, you can burn out valves if you use too much, and I believe they recommended stainless valves if you were going to use it.

  • 5 weeks later...

2 questions...

1) What is the shelf life of toulene? ie) if I get 200L from shell or bp can I use 10L a week with every tank for 20 weeks - will the last 10L be just as good as the 1st 10L batch?

2) Do you have to shake it vigorously with petrol before hand to properly mix it? or can you just add it straight then add the petrol and will driving and cornering mix it up enough?

sorry for the questions - didn't do chem in school!

  • 2 months later...

So will there be any differences in the ways we can add toluene (other than method B being more time consuming)???

Method A: Go to a petrol station with an empty tank, first add petrol or toluene and than add the other.

Method B: Mix them at your garage, shake well :rofl: and than add to your petrol tank.

Also will a 95 octane petrol increased to 98 octane by using toluene be the same or as good as a genuine 98 octane petrol (optimax, bp, mobile )???

Some mechanic mentioned that a 95-96 octane petrol increased to 98 by using octane boosters wont be as good as geniune 98 petrol when tuning the car :confused:

Incidently if you want to use it legally as fuel you need to approach the appropriate? Gov dep. and arrange to pay the fuel exise to them on any amounts you buy. I don't know as yet if this applies when you are using it in small amounts as an octane booster. EDIT: It is sold as a solvent and as such does not attract fuel tax thats's why it is relativly cheap. If you use it as a fuel then you are legally required to contact the appropriate gov dept and pay them the fuel tax due on the amount you use as fuel. The only question is .... is an octane booster counted as fuel.

Surely if you were using it as an Octane Booster for Track use it would be exempt from fuel excise? It certainly couldnt be illegal on the track, could it?

REV210: Did you change the C.A.S? How many degrees, if any?

Toluene Octane Booster sounds good. I was talking about it with a friend of a friend 2 days ago, who is a Petro-Chemical Technician or something and he said you would only need a Cup-full to make a difference, I realise this conflicts with all of your mixture levels mentioned here, maybe he has been sniffing it too much :P I am glad somebody re-dredged this thread from the ether :( 10-20% sounds like a good level.

Any one tried it with Synergy 8000. I am able to run more timing @ 16psi compared to when I run BP98. BP98 causes the car to go flat for a sec then pics up and then goes flat again. Running less timing fixes the power loss/dip feeling but that isn't the point :D

A similar thing happens to my car with BP98, I have tried Synergy a couple of times and the problem is not noticeable... Synergy is further away and more expensive - as you mentioned.

Cheers.

So will there be any differences in the ways we can add toluene (other than method B being more time consuming)???

Method A: Go to a petrol station with an empty tank, first add petrol or toluene and than add the other.  

Method B: Mix them at your garage, shake well :( and than add to your petrol tank.

Also will a 95 octane petrol increased to 98 octane by using toluene be the same or as good as a genuine 98 octane petrol (optimax, bp, mobile )???

Some mechanic mentioned that a 95-96 octane petrol increased to 98 by using octane boosters wont be as good as geniune 98 petrol when tuning the car  :confused:

So no one knows???

So no one knows???

If you wait a bit, the original thread starter + others who have contributed to this topic will see it and perhaps provide input to your query.

Patience O-B-1, people are probably on holidays, like me :) [but not online].

:P

I am guessing that Method A would be the go.

How do you explain to them [at the servo] why you want to put 50 Litres of BP Ultimate 98 into a Jerry can...? For your supercharged ride-on lawn mower? Lol...

I don't think they would knowingly let you *mix up molotov corcktails* in your backyard.

:Bang:

BOOSTMEISTER

we ran a lexus v8 twin blown on c16 with great results, we ended up have 40 psi, 6:1 comp with 32 deg advanced with no det. used shit loads of fuel but sounded amazing. when we were turning this engine it didnt seem to perform untill we advanced the timing so far, something you might want to try next time Roy.

I'm also very interested in setting my car to use this fuel also, there was a article in some mag where they set up a gtr to run on c16, how ever i cant remember the results. From my memory c16 is made for forced induction engines. i would be extremly interested to hear your results if you go down this line. c16 does also have a slight lead content which will mean cleaning your 02 sensors.

Matty B

I am guessing that Method A would be the go.  

How do you explain to them [at the servo] why you want to put 50 Litres of BP Ultimate 98 into a Jerry can...? For your supercharged ride-on lawn mower? Lol...

I don't think they would knowingly let you *mix up molotov corcktails* in your backyard.

:Bang:

If you own oil manufacturing facilities it's quite possible to buy any chemical and petrol you want in bulk :D

And how about quality of 98RON vs 95RON+toluene ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...