Jump to content
SAU Community

Recommended Posts

Hi,

Been told to take some holidays at work and was thinking of taking the car for a spin south to Victoria and trying to catch an event or two, looks like the Hillclimb is on at Haunted Hills on the Saturday which sounds like fun but wondering if anyone knows of any other events that week for any of the tracks (PI would be great) or even some meet ups in Vic to check out the seen.

Really want to make the most of my time if possiable,

Matt

Edited by boxheadmr
Link to comment
https://www.sau.com.au/forums/topic/306104-week-comencing-08022010/
Share on other sites

It looks like there is plenty of spots available and if you get in before the 8th is a little cheaper. I would love to do Haunted Hills as have heard it is the best hillclimb in the county but the chance at 2 days at PI looks too good an oppatunity to pass up.

Is there much on at winton for the trip back?

It looks like there is plenty of spots available and if you get in before the 8th is a little cheaper. I would love to do Haunted Hills as have heard it is the best hillclimb in the county but the chance at 2 days at PI looks too good an oppatunity to pass up.

Is there much on at winton for the trip back?

Your on the money, 2 days at the best track in Aus is way too hard to pass up. Just make sure you have fresh tyres/pads and heaps of fuel!!!!

Will most likely head down for a looksee, a few people I know are racing both days....

Picking up some fresh tyres this week and like the reports on the medium new A050's so will give them a try, picked up some new pads and fluid as well.

Thanks for the tip with the fuel and will pack the extra jerry cans, is it pricy the fuel at the track or best to drive to San Remo for a splash and dash. I would imagine the Saturday practice would go through the fuel the most.

Any tips for where to park-best to get a garage, food etc?

Matt

Picking up some fresh tyres this week and like the reports on the medium new A050's so will give them a try, picked up some new pads and fluid as well.

Thanks for the tip with the fuel and will pack the extra jerry cans, is it pricy the fuel at the track or best to drive to San Remo for a splash and dash. I would imagine the Saturday practice would go through the fuel the most.

Any tips for where to park-best to get a garage, food etc?

Matt

Matt, have heard good things about the new A050's, what do you usually use? And by the way, what car will you be entering??

My advice would be to fill your tank in your car to the brim, assuming you haven't been to PI before you will not be doing your quickest laps on Saturday morning.

Fill up a few jerry cans aswell. What fuel do you use? If normal 98 than that's not a problem, san remo would be the go, if you use 100 octane then the closest servo is about 60k's away...

You will get heaps of laps in on Saturday, you'll be using more fuel Sat than Sunday timed sprints.....

Been using RE55's for a while now but have tried out the R888's and AO48's previously but seemed to get the best wear and good times out of the RE55's. As a hot lapper the R888's seemed to do well from what i expeienced.

Yeah thought as much with the fuel on the Saturday, hopefully the weather will be OK (have jinked myself now) and not show it's usual form for PI that you see on the TV or every time i have been there to check out the racing.

I am not sure how it works at PI,

Thanks for that will give me an idea of how i am going on the lap timer. hopefully i am not wasting too much time with all these questions of everyone and apresiate the guidence. Is any of the SAU Vic team heading out on the Sunday or Saturday (bearing in mind the HH event).

Matt

Thanks for that will give me an idea of how i am going on the lap timer. hopefully i am not wasting too much time with all these questions of everyone and apresiate the guidence. Is any of the SAU Vic team heading out on the Sunday or Saturday (bearing in mind the HH event).

Matt

Your not wasting anyone's time here mate, we're all one big family!!!!

Not sure who's racing from SAU, BBGTR usually attends this meeting, look out for a very quick black 32GT-R.

I'll be there for a looksee...

Oh, and what car are you entering???

Will be in a white wide body S14a, race number is 539 but not sure if this is taken down there.

Just sent off my entry forms this morning to get the early bird special, wish i realised you didn't need to join the club to enter and just be part of a cams affiliated club but had already got the money order.

Looking forward to it and to saying hello.

Matt

  • 2 weeks later...

Thanks Roy and the rest of the SAU Vic crew who I meet on Sunday, you all were really good blokes and appreciate the tips you passed on.

I was surprised with how friendly the day was with the PIARC, Dave with the 32GTR was a real champion and a good steerer along with the guys in the Mini and WRX. Not sure if he is on SAU but thank you for assisting and for also splitting the cost of the garage.

PI is really in a class of its own with super fast - flowing corners, a lot better then any of the other tracks I have been on and so much more rewarding. The facilities and track surface seem second to none.

I didn't get home till late last night after fixing a few issues with the car.

Trip back was good but scored a nice little surprise from a little light blue subie forester with a flashy light thing right at the bottom of a down hill section of the road.

106klm/h in a 100 zone downhill - got to love Victoria!!!

Who was the person with the camera? Any chance of getting some of the photos you took?

Thanks again for all your help guys and hopefully will be back down with a leave pass in the not too distant future.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...