Jump to content
SAU Community

Recommended Posts

Hi all,

I'm trying to get a N1 engine identified whilst still in the car. Can anyone tell me where I would find the I.D. numbers? I know I'm after the '24U' stamped on the block....I just don't know where to find it. The car is interstate so I need to let the owner know where to look.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/306166-engine-locaion/
Share on other sites

If its in the same spot as my rb25det. Its located on the passenger side on the block just above the sump and next to where it joins the gearbox. There is a smooth section where it will be stamped on. Mine was hard to read.

Link to comment
https://www.sau.com.au/forums/topic/306166-engine-locaion/#findComment-5063082
Share on other sites

+1..all stamped right on the bell housing, down low, behind the turbo.

To read mine, I had to remove the heatshield...and because it was hard to read...I had to setup a worklight under the passenger side wheel, shining pretty much side on to that flat section with the number...only just barely readable then...I've gotta get around to engraving the numbers deeper.

Link to comment
https://www.sau.com.au/forums/topic/306166-engine-locaion/#findComment-5063140
Share on other sites

The "24U" engine code is not actually stamped on. It's part of the casting of the N1 block. If you want to find the engine number, it's on the driver side near the front on the block. Just checkout the pic. The numbering will go like this:

RB26xxxxxxX

"x" denotes the engine number sequence. "X" means it's an N1 or Nismo block. A standard 05U block with have "A" instead of "X".

post-2802-1264932681_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/306166-engine-locaion/#findComment-5063632
Share on other sites

Awesome cheers for the help guys. Any other easy way (I know the turbos are different?) besides the no rear windscreen wiper & no stereo? I'm just wanting to make sure as the one I'm looking at has got a rear windscreen wiper but the owner is totally sure its a N1. I can only ssume the possibility of the rear windscree nwiper being installed for compliance. Even if its just a clean GTR with a N1 engine (the whole thing...Cams, Block, Turbos etc etc) I'll be happy. If its just the block and the rest is standard GTR I'm not too sure.

Link to comment
https://www.sau.com.au/forums/topic/306166-engine-locaion/#findComment-5064020
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...