Jump to content
SAU Community

Recommended Posts

Catkicker. There is a textbook amount. On the ugly poo gtr/gtr33/gtst33 the amount is about 3.8L. But you can never get it all out.

I normally get in 3.5-3.6L. That's why you just fill it till it comes out when the car's level. If you tried to put in 3.8L, it would all just pour out the side filler hole.

On the r ugly poo gtst, i believe the amount is about 2ish litres. Just fill it till it comes out then bung it.

Yeah, 3.8L will be heaps for the r32. You should have a fair bit left over for top ups/doing a mini change later or something.

For the r33s, 3.8 is touch and go. I have used almost 4 L once, but that was a dry fill (box dissasembled).

PS: have you looked at the redline website - shockproof is not recommended for boxes with synchros. Just thought i'd tip ya on that

Edited by MANWHORE

Yeah I have heard that but a lot of people use it and rave about it. However then there are 2 sides to every story and others have used it and blown gearboxes.

From what I have read, it is excellent if your box is getting tired (ha ha) but I am not sure if there is something more suitable. I am starting to get occasional crunching in 1st and 2nd so figure there is no harm in trying it... Can anyone reccomend anything better?

You are spot on about two sides of the story.

Yes, it does give superb feel. Automatic transmission fluid also gives great feel too, but isn't good for your box either.

I personally haven't used shockproof in my car. One of my friends is using it, and it made a huge difference in feel (then again, even putting cooking oil would have because the oil had probably never been changed since factory. It was almost like mud).

I personally use and stand by motul gear 300. It's fully synthetic and it's about the same price as shockproof. About $30 a litre.

  • 2 years later...
  • 4 weeks later...

Just one thing i feel like adding to this, is if youre like me, and have had to work on an R32 that is (illegally) low, so low you cant even get your arm under it.... then there is another way to get the oil in, other than the filler bung.

We ended up jacking one side of the car up a little, so you could JUST get your fingers on the filler bung (to put it back in), and since the box had just been out, the shifter wasnt installed. We then proceeded to fill the box, using a funnel made of an old 2.25 sprite bottle, through the shifter hole, untill it started to dribble out of the filler hole. When that happened, we all poo'd our pants and my mate jammed his arm up under the car to put the bung back in place.

Of course, car was too low to tighten it up like that, so we had to jack the whole car up enough to get under and tighten bung back up. Put shifter back on, and tell kid to come pick his stupid car up and get it out of our sights.

That, is my life story.

  • 2 years later...

Did mine today. Wasn't as hard as I thought it would be. From my experience here are a few tips

If you are having issues with getting the drain plug undone, leverage is key.

If you have access to a hoist, run some flush through the box then drain that as it gets rid of excess oil to allow for your new clean oil

I used a pressure spray bottle 2L and it pretty much did all the pumping work itself, I took the one I brought from SCA back as it broke within 30seconds...

Also, if you for some reason cannot get your fill plug out, it may be easier to fill it through the reversing switch. I wouldn't recommend it but is a last resort kind of thing.

Now to go make a CAI and light up skyline sign :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...