Jump to content
SAU Community

Recommended Posts

Hey guys just pulled out my fuel pump and found to be stock, so will be upgrading soon.

Also decided to check voltage supply to pump as i've noticed few complaints (mainly r32) of voltage drop under load.

Battery voltage varied between 13.3v - 13v

Fuel pump voltage sat around 12.9 - 13v at idle and cruising, but dropped as far as 12.6v when I planted my foot into it.

Anybody reckon this is cause any probs for pump? or should I just direct feed it to battery anyway.

Also looking at Nismo, Tomei or HKS fuel pump. Is there actaully any difference between them. All around the same price.

Cheers :happy:

Link to comment
https://www.sau.com.au/forums/topic/306832-r33-gtr-fuel-pump-voltage-drop/
Share on other sites

Hey guys just pulled out my fuel pump and found to be stock, so will be upgrading soon.

Also decided to check voltage supply to pump as i've noticed few complaints (mainly r32) of voltage drop under load.

Battery voltage varied between 13.3v - 13v

Fuel pump voltage sat around 12.9 - 13v at idle and cruising, but dropped as far as 12.6v when I planted my foot into it.

Anybody reckon this is cause any probs for pump? or should I just direct feed it to battery anyway.

Also looking at Nismo, Tomei or HKS fuel pump. Is there actaully any difference between them. All around the same price.

Cheers :happy:

Don't waste your money, get a Bosch 044 and mount it in tank with a relay so it gets full battery voltage. Look in DIY section.

Nothing a bit of insertion rubber and a couple of hose clamps can't fix!

Yeah true but I reckon fuel surge would be a fair bit worse with that sort of setup. I guess if you dont track it its not a problem.

Hi. I had a similar problem in my gtr whilst getting it tuned. There is a fuel pump speed controller in some models of the 33, to bypass it, run a ground/negative wire from the pump directly to the chassis/battery. remember, ONLY do the negative as this is what controls the pump speed. Its a 5 min excercise and if it is the fix you were after, then choice. If its not, then hey, 5 mins and 40cm of wire is bugger all right?

Cheers, Allan

yes it is the fuel pump voltage regulator. It keys off the ECU, and varies the pump voltage according to engine load.

Unfortunately it is not able to drive the pump at full load without caving in (which is seen by a big dump in voltage).

So instead of wasting money on a new pump, just wire it to negative and you'll hear it is louder at idle, and you're also recirculating a lot more fuel back into your tank too, which might lead to fuel heating issues if your tank is nearly empty and you are in heavy traffic on a hot day.

but it solves the problem.

my advice is get the nismo pump. they are direct bolt in and work very well and very reliably. I have not seen one problem or failure of one EVER. I have seen a number of bosch pump failures though and others that did not live up to their flow claims. as best I can tell the nismo/tomei/HKS pumps are all the same so chose which ever one you can get quicker or cheaper.

adding a direct feed from battery to the pump (with a relay) is a good idea too. regardless of which pump you get.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...