Jump to content
SAU Community

Recommended Posts

i didn't know where else to post this as its not really general maintenance, but as the title says, i got a problem with my air con! it's an R34 GTT

what was originally happening was the complete opposite, i had super cold air on 18 degrees, then anywhere from 18.5 - 32, would be super hot, like instant jump from actual 18 degrees to actual 32 degrees even on '18.5'

and i had my dash cluster out the other day replacing a backlight, and noticed that the little plug and hose that connects to the spot behind the facia that detects the inside-car temperature had always been unplugged since i bought it, so i plugged it back in thinking YES i found something wrong and fixed it, anyway, gave it a test, and now it's doing the complete opposite, it's complete coldness all teh way through the temperature range from 18 to 31.5, and at 32 its super hot.

whats the go here?

would there be another sensor somewhere not plugged in causing this like the in-car temp one was? or something else?

thanks for any help,

Brad.

Link to comment
https://www.sau.com.au/forums/topic/306852-air-con-problem-on-r34-gtt/
Share on other sites

so i plugged it back in thinking YES i found something wrong and fixed it

hahaha, sorry i just found that funny

and i had my dash cluster out the other day replacing a backlight

at least you didnt short circuit your cluster like i did.

regarding your actual problem im unaware of any other sensors, i think the one you plugged in was the only one, it may be your actual climate control unit playing up. if you have access to a mates unit, swap them out to see if it is a faulty unit or not.

otherwise i cant think of much else.

cheers

Edited by BXAFTW

mine does the same man... i cant remember how but some guy in brisbane here who specialises in skylines performance etc fixed his and i asked him to fix mine.. he did say wat it was but i cant remember.. sorry mate but it is only a sensor stuffin up in behind there

  • 2 months later...
  • 1 month later...

probably your cabin temp sensor unplugged, that was my problem and now all is well.

follow these instructions to figure out what sensors are failing

http://www.skylinesaustralia.com/forums/Ai...p;hl=diagnostic

remember the sun sensor will register as failed at night.

r34's do not have hot and cold buttons, instead slowly turn the climate control dial from left to right to enter the different diagnostic modes. the mode you want is about an 8th to a quarter turn i think, and it'll flash the appropriate numbers.

if it flashes 22, then your inside cabin temp sensor is not working. it is often left unplugged after work is done in the drivers side foot well. the sensor is behind a plastic grate on the left side of the steering wheel. to get at it do a search in diy, but from memory there's about 6 bolts to find to get the large bit of plastic off from under the steering wheel, then lower the steering wheel as far as it'll go and take the plastic off from around the speedo etc, then its a white plug just behind the grate.

good luck mate

ey mate,

that did it.

i've been driving around with cluster perspex cover off (and that plastic surround covering it) because i'm replacing the cover soon and didn't want to bother with the hassle of taking off everything.

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...