Jump to content
SAU Community

Recommended Posts

hey guys, was changing my plugs and i noticed that my plenum seems to have lifted by 2-3mm

is it something that i should just tighten and forget? does it need a new gasket? what could have caused the issue?

the car still makes and holds 18psi with no excess noise...

you can also see all the filth around the gasket

it is however probably 3-500rpm laggier... at first i thought i was just imagining it...

med_gallery_36777_3194_287857.jpg

med_gallery_36777_3194_304934.jpg

?

Link to comment
https://www.sau.com.au/forums/topic/308329-plenum-gasket-lifted-by-a-few-mm/
Share on other sites

shit.... just had a thought...

car was riching out and fouling plugs, so we retuned it from the ground up about 3 months ago...

is there any chance that air was escaping through the gasket and thus making the car rich?

because that means if i fix it then i'll be leaning the car out... :)

quick retune perhaps?

41jQywGYTmL._SL500_AA280_.jpgAlso, for this type of job and for almost any job, one of these bad boys are the ultimate. the whole case is around 60-70mm long and they fit in the tighest of tight places, yes where the sun does not shine.

Tough as nails, I regularly slug mine with a 4 pound hammer. Only goes up to 13mm But you can by extra sockets (any brand) if you need them bigger. this & a set of ratchet spanners is very handy indeed.

made by Teng tools.

Interesting, mine has the exact same thing going on hamish, and I also have the car runningly stupidly rich and fouling plugs all the time. It dosen't look like it would be a massive job to take it off, apart from the bolts lol, I'm used to having to pull my cooler piping and associated hosing all the time to get to the spark plugs anyway.

ratchet spanners are a must on a Skyline IMO, too fkn hard and complicated to do a lot of things otherwise.

tweak the outer ones and with the car idling spray aero start or brake / carb cleaner around the gap. If the idle lifts (or any perceptible change) you have a leak.

Remember the gasket is rubber and around 3mm thick so it should not look flush, but the oil around it is a bit sus :)

Mind you when we were chasing your leak on the dyno i remmember spraying cleaner around there and it was fine @ idle. (but it was not oily then) then we found the split cooler elbow.

Yeah what is with all that oily residue on the outside of the plenum :)

I think if the tune was thrown out by that the leak would have to be pretty substantial and you would notice is very easily. I wouldn't worry about the tune side of things, just fix it up and if you are worried chuck it back on Trents dyno.

Edited by PM-R33

REMEMBER.

There are 2 types of gaskets on the R33 skyline. One is completly all rubber and the other is rubber with metal bracing on the insides to keep its shape.

100% of the time i have seen the the complete rubber ones have leaked and caused ALL kinds of issue.

Do not start this job untill you get the gasket that has metal inside to keep its shape.

If you can bend the gasket """" IT IS THE WRONG ONE """"

And to rest your mind about the leaking issue (tuning).. when they leak from there the plenum will SCREAM "EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE" very high pitched sound. (personal experience - hence the 2 types of gasket comment)

thanx ant :thumbsup: i'll make sure to check first!

i would have thought there would have been a noise if it was leaking too.... but the thing that gets me is the residue all around the gasket...

that engine bay copped 3 cans of degreaser only 6 months ago...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...