Jump to content
SAU Community

Recommended Posts

hey guys, was changing my plugs and i noticed that my plenum seems to have lifted by 2-3mm

is it something that i should just tighten and forget? does it need a new gasket? what could have caused the issue?

the car still makes and holds 18psi with no excess noise...

you can also see all the filth around the gasket

it is however probably 3-500rpm laggier... at first i thought i was just imagining it...

med_gallery_36777_3194_287857.jpg

med_gallery_36777_3194_304934.jpg

?

Link to comment
https://www.sau.com.au/forums/topic/308329-plenum-gasket-lifted-by-a-few-mm/
Share on other sites

shit.... just had a thought...

car was riching out and fouling plugs, so we retuned it from the ground up about 3 months ago...

is there any chance that air was escaping through the gasket and thus making the car rich?

because that means if i fix it then i'll be leaning the car out... :)

quick retune perhaps?

41jQywGYTmL._SL500_AA280_.jpgAlso, for this type of job and for almost any job, one of these bad boys are the ultimate. the whole case is around 60-70mm long and they fit in the tighest of tight places, yes where the sun does not shine.

Tough as nails, I regularly slug mine with a 4 pound hammer. Only goes up to 13mm But you can by extra sockets (any brand) if you need them bigger. this & a set of ratchet spanners is very handy indeed.

made by Teng tools.

Interesting, mine has the exact same thing going on hamish, and I also have the car runningly stupidly rich and fouling plugs all the time. It dosen't look like it would be a massive job to take it off, apart from the bolts lol, I'm used to having to pull my cooler piping and associated hosing all the time to get to the spark plugs anyway.

ratchet spanners are a must on a Skyline IMO, too fkn hard and complicated to do a lot of things otherwise.

tweak the outer ones and with the car idling spray aero start or brake / carb cleaner around the gap. If the idle lifts (or any perceptible change) you have a leak.

Remember the gasket is rubber and around 3mm thick so it should not look flush, but the oil around it is a bit sus :)

Mind you when we were chasing your leak on the dyno i remmember spraying cleaner around there and it was fine @ idle. (but it was not oily then) then we found the split cooler elbow.

Yeah what is with all that oily residue on the outside of the plenum :)

I think if the tune was thrown out by that the leak would have to be pretty substantial and you would notice is very easily. I wouldn't worry about the tune side of things, just fix it up and if you are worried chuck it back on Trents dyno.

Edited by PM-R33

REMEMBER.

There are 2 types of gaskets on the R33 skyline. One is completly all rubber and the other is rubber with metal bracing on the insides to keep its shape.

100% of the time i have seen the the complete rubber ones have leaked and caused ALL kinds of issue.

Do not start this job untill you get the gasket that has metal inside to keep its shape.

If you can bend the gasket """" IT IS THE WRONG ONE """"

And to rest your mind about the leaking issue (tuning).. when they leak from there the plenum will SCREAM "EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE" very high pitched sound. (personal experience - hence the 2 types of gasket comment)

thanx ant :thumbsup: i'll make sure to check first!

i would have thought there would have been a noise if it was leaking too.... but the thing that gets me is the residue all around the gasket...

that engine bay copped 3 cans of degreaser only 6 months ago...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...