Jump to content
SAU Community

My Car And Some Other Shots

AKW

By AKW,
in Photography

 Share

Recommended Posts

iadore4door34s Enthusiast

iadore4door34s

Posted
Posted

Some nice pics there bro.. especially the one of the barn and i reckon if you bumped the sat up a bit you could really get those colors (note spelling aus boys :cheers: hahahaha) where in the states are you located??

good to see there are some skylines kicking around the states as i had heard that it was a real bitch to get them registered for road use.. heard many a stories on zilvia doing dodgy things with numberplates from other cars and the such.. care to shed some light on the situation?

AKW Enthusiast

AKW

Posted
  • Author
Posted

Yeah I really like the picture of the barn. I bumped up some saturations already believe it or not, it was the greyest day. That's our barn BTW.

And yeah, the car was titled and released here in the states. I got it for graduation from my mother.

GoldZilla Grand Master

GoldZilla

Posted
Posted
Some nice pics mate, but...

A GTR wing and GTR badge does not make it a GTR. PLEASE get rid of that badge asap!! :P:sick::ninja:

Agreed, on both counts - great photos, nice car, but that GTR badge has got to go...

AKW Enthusiast

AKW

Posted
  • Author
Posted (edited)

I am not pretending it is a GTR, but I don't have anything to replace it with either. That is a real GTR front grille. I don't know what I would be able to even get to fit it. I don't intend for it to be a GTR, but that sure looks better than that stupid cut-up grille they give you, and that wing is yum compared to the GTST as well. If I were going that route it would be one on the back lol. But I know it is a GTST. Anything to fit a real GTR grille? Point it out please...

Edited by AKW
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...