Jump to content
SAU Community

Recommended Posts

Apparently a blue skyline (dunno what model) was crashed into a house this morning when the car was pulled up for a routine traffic check and the driver took off. Anyone know anything about this? God I hope it was stolen in the first place (would hate to think anyone on here is that fking stupid) and I HOPE it wasn't JD's...though I dare say we'd already know more if it was

Nah, twas not I.

But even the mother-in-law had to ring this morning to make sure. I told her I had to speak softly because I was under the bed, and I thought the police were at the door. Had her going for a good 5 minutes.

Crash actually happened in Ellerston Ave, so more Isabella Plains than Calwell.

*It's Melly*

Just saw it on the news, was making dinner heard skyline ran around the corner (bad idea in socks on lino) and saw it, they didn't show the colour or car which is unfortunate because that we would have at least know what model and what sort of blue.

I only heard a little bit of this and THOUGHT that I heard that it was a stolen dark blue 4 door R34 from a lady in Chisholm... But again, I only heard just a little bit of it so it could have been two stories in one by the time I paid attention.

I heard this article too and straight after there was a lady in that area that had her pulsar stolen so it may have been 2 in one.

Probably was just two seperate incidents then. Ignore me :no:

Lol, FoX, unfortunately??

Nah, twas not I.

But even the mother-in-law had to ring this morning to make sure. I told her I had to speak softly because I was under the bed, and I thought the police were at the door. Had her going for a good 5 minutes.

Crash actually happened in Ellerston Ave, so more Isabella Plains than Calwell.

Thats gold :no:

Sounds like a P-plater or stolen car to me. But I am biased against p-platers and car thieves in general...

Thats gold :P

Sounds like a P-plater or stolen car to me. But I am biased against p-platers and car thieves in general...

Understandable, but we aren't all bad. I've never done damage to another persons car but I've had damage done to mine on 3 separate occasions. But those P platers are bastards. :(

Thats gold :D

Sounds like a P-plater or stolen car to me. But I am biased against p-platers and car thieves in general...

Understandable, but we aren't all bad. I've never done damage to another persons car but I've had damage done to mine on 3 separate occasions. But those P platers are bastards. :O

So which one are you? The car thief or the P plater ;):):P

Understandable, but we aren't all bad. I've never done damage to another persons car but I've had damage done to mine on 3 separate occasions. But those P platers are bastards. ;)

So which one are you? The car thief or the P plater :P:P:P

holy crap! its Michele!!! :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...