Jump to content
SAU Community

Recommended Posts

I have a pretty stock r33 with a intercooler, blow of valve and a air filter which all other parts being stock i think and recently took my car for a service/tune. Sorry if i sound stupid in advance i dont know much about cars and i tried using the search function. The guy said fuel pump was broken and replaced it but i was wondering how the fuel pump would brake so i can avoid making the same mistake?

Also i got it on the dyno and got 188kw running at 11.5 pounds of boost. Is that normal ? I've also been wanting to start working my car up but am a bit lost with where to start. Is there a general guide on these forums to help me get started or educate with the basics of what i need to know ? Also, if i want to start working on my car where should i start and what are quick things i can do that arent too expensive to increase performance ? thanks in advance !

Link to comment
https://www.sau.com.au/forums/topic/311122-general-help-with-r33-gtst/
Share on other sites

ok, the fuel pump just wears out over time and there isn't anything in particular you can do to prevent it. find out what sort of pump he replaced it with as this may be something that you need to look into when upgrading further. if he went with something like a bosch 040 then you will be fine, but if he only went with a stock unit then if you start chasing more power it might be worth upgrading to a better unit (such as the bosch i listed).

you listed your mods, but didn't mention the exhaust. does it have a bigger exhaust, or just the stock system? i'm guessing by your power figure that it would probably have a 3" exhaust as you would struggle to make that power with the stock one. but that power level is about right for that boost level and those mods.

as for modifying it, firstly, if any of the exhaust is still stock, such as the dump pipe, then i'd start by upgrading that. after that you are pretty close to the limit of what both the stock ecu and stock turbo will handle. the turbo will go a bit higher, but the life expectancy of it dramatically shortens. there are many options when it comes to upgrading both ecu and turbo, but depending on how far you want to take it you may be going into the area where other mods are needed such as injectors and AFM as they don't go that far beyond the stock ecu and turbo. many people will tell you to go with a pfc as a replacement ecu, but personally i would go with a z32 ecu and a nistune daughterboard. this will set you back about half of what a pfc will and do pretty much the same thing.

hey i wasn't sure which part of the exhaust you were talking about so i figured the easiest way was to take a few pictures of mine. Do you think i need a upgrade with this exhaust?

Also another question regarding the computer. Do i need to get it tuned or whatever everytime i get a upgrade? so if i do upgrade the exhaust would i need to get it tuned again ? if not when do i need to get these things done as im not quiet sure ! thanks alot for the help !

post-45881-1268136815_thumb.jpg

post-45881-1268136900_thumb.jpg

post-45881-1268136963_thumb.jpg

post-45881-1268137009_thumb.jpg

if any of the exhaust is still stock, such as the dump pipe, then i'd start by upgrading that.
hey i wasn't sure which part of the exhaust you were talking about so i figured the easiest way was to take a few pictures of mine. Do you think i need a upgrade with this exhaust?

if its a 3" exhaust from the cat converter back (ruffly located under the passenger seat section of the car), then upgrade it from the turbo back to make it a complete 3" turbo back exhaust (ie. dump pipe, front pipe and cat converter)

hey i wasn't sure which part of the exhaust you were talking about so i figured the easiest way was to take a few pictures of mine. Do you think i need a upgrade with this exhaust?

Also another question regarding the computer. Do i need to get it tuned or whatever everytime i get a upgrade? so if i do upgrade the exhaust would i need to get it tuned again ? if not when do i need to get these things done as im not quiet sure ! thanks alot for the help !

with the stock ecu you can't actually tune it, so you don't need to do anything when you upgrade things, however somethings you upgrade require an aftermarket ecu to run them. a good example of this is if you put in bigger injectors. the stock ecu is setup to think that the injectors are 370cc, so if you go and put in bigger ones it will still think it has 370cc ones in there and be dumping in way too much fuel and you'll be luck if the car will even start.

things like a bigger turbo will require an aftermarket ecu and for it to be tuned if you want to run bigger boost, however they can be run on the stock ecu at very low boost as they will still be in the paramaters of the tune on the stock ecu. you just wouldn't really make any more power than on the stock ecu.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...