Jump to content
SAU Community

Recommended Posts

* One Top Fuel dragster 500 cubic inch Hemi engine makes more

horsepower than the first 4 rows at the Daytona 500.

* Under full throttle, a Top Fuel dragster engine consumes 1&½ gallons

of nitro methane per second; a fully loaded 747 consumes jet fuel at

the same rate with 25% less energy being produced.

* A stock Dodge 426 Hemi V8 engine cannot produce enough power to drive the

dragster's supercharger.

* With 3000 CFM of air being rammed in by the supercharger on

overdrive, the fuel mixture is compressed into a near-solid form

before ignition. Cylinders run on the verge of hydraulic lock at full

throttle.

* At the stoichiometric 1.7:1 air/fuel mixture for nitro methane the

flame front temperature measures 7050 degrees F.

* Nitromethane burns yellow. The spectacular white flame seen above

the stacks at night is raw burning hydrogen, dissociated from

atmospheric water vapor by the searing exhaust gases.

* Dual magnetos supply 44 amps to each spark plug. This is the output

of an arc welder in each cylinder.

* Spark plug electrodes are totally consumed during a pass. After 1/2

way, the engine is dieseling from compression plus the glow of exhaust

valves at 1400 degrees F. The engine can only be shut down by cutting

the fuel flow.

* If spark momentarily fails early in the run, unburned nitro builds

up in the affected cylinders and then explodes with sufficient force

to blow cylinder heads off the block in pieces or split the block in

half.

* In order to exceed 300 mph in 4.5 seconds dragsters must accelerate

at an average of over 4G's. In order to reach 200 mph well before

half-track, the launch acceleration approaches 8G's.

* Dragsters reach over 300 miles per hour before you have completed

reading this sentence.

* Top Fuel Engines turn approximately 540 revolutions from light to

light!

* Including the burnout the engine must only survive 900 revolutions

under load.

* The red-line is actually quite high at 9500 rpm.

* The Bottom Line; Assuming all the equipment is paid off, the crew

worked for free, and for once NOTHING BLOWS UP, each run costs an estimated

$1,000.00 per second.

* The current Top Fuel dragster elapsed time record is 4.441 seconds for

the

quarter mile (10/05/03, Tony Schumacher).

The top speed record is 333.00 mph (533 km/h) as measured over the last 66'

of the run (09/28/03 Doug Kalitta).

Putting all of this into perspective:

You are riding the average $250,000 Honda MotoGP bike.

Over a mile up the road, a Top Fuel dragster is staged and ready to launch

down a quarter mile strip as you pass.

You have the advantage of a flying start.

You run the RC211V hard up through the gears and blast across the starting

line and past the dragster at an honest 200 mph (293 ft/sec). The 'tree'

goes green for both of you at that moment.

The dragster launches and starts after you.

You keep your wrist cranked hard, but you hear an incredibly brutal whine

that sears your eardrums and within 3 seconds the dragster catches and

passes you.

He beats you to the finish line, a quarter mile away from where you just

passed him.

Think about it, from a standing start, the dragster had spotted you

200 mph and not only caught, but nearly blasted you off the road when

he passed you within a mere 1320 foot long race course.

That, folks, is acceleration !!

for fark sake this has been posted on every known car forum atleast twice before :D

I beg your pardon ! I am so sorry for invading into your personal forum reading time. I didn't realise that this had been posted before as I hadn't seen it myself and I thought maybe some others may enjoy.

Feel free to igonore my post or if it annoys you so much, I can delete it at your conveinience.

:upurs:

:)

:)

:)

:D

Thanks for that read dude. Cant wait to go to the drags again when they open the new strip at eastern creek. I used to go all the time to calder prk when i lived in melbourne. The smell of the exhaust fumes is something else. It seriously burns your throat and singes nose hairs.

Wish the skyline had that sort of effect, without the running costs of course.

Damo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...