Jump to content
SAU Community

Recommended Posts

Hey guys,

I was looking around under the bonnet when i touched this piece very lightly and the lead in the middle broke off. It seemed to be quite corroded and fragile. Any ideas what this thing does? The leads go for miles around the engine bay and seem to end up down near the right front suspension.

Thank you!!

I hope the pics are good enough

post-66386-1268734177_thumb.png

post-66386-1268734214_thumb.png

Link to comment
https://www.sau.com.au/forums/topic/312178-broken-what-is-it/
Share on other sites

So a line goes from it to the manifold and another goes, via some container, to the fuel tank. It's apparently a solenoid which hs something to do with controlling the air-fuel mixture, except now instead of sucking in more petrol, its sucking in more air.

Didn't notice any difference on a drive, but it was corroded and may have been leaking all along.

Where should i look to find a replacement piece?

i have the same solenoid on my stagea, being a NEO engine too. i've followed the lines and tried to figure out what it does, and from what i can tell its the carbon canister purge control valve. i think it does the same job as the vacuum controlled purge valves on the older model skyline carbon canisters. if you follow the line you will see it goes to the carbon canister (small black cylinder nest to the airbox/pod).

i'm not 100% on the operation of a carbon canister. but i know it has something to do with fuel vapour building up pressure in the fuel tank, and when your car is running the build up pressure goes through the canister and then released back into the inlet manifold when the engine is pulling vacuum. i guess by not having an operation carbon canister, you will get a build up of pressure in the fuel tank. again i'm not 100% on how it works, i think you'll find there are people that don't run them and don't have a problem.

edit: check this webpage out for information LINK

if your keen to get it replaced just remove it from the engine, its not doing anything at the moment anyway. then take it to an import wreckers and see if they have one. you should be able to get one through nissan but it will be cheaper trying the wreckers first

Edited by QWK32

Thanks for the link mate, very interesting. Just wondering how much I'd expect to pay for this part? And what consequences I'm facing without the solenoid working?

Also, just for interest, how much would i expect to pay for the cold air intake snorkel thing that attaches to the stock airbox?

thanks for any info

  • 2 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...