Jump to content
SAU Community

Recommended Posts

Ok to cut a long story short, I did have a look thru the various wheel threads but they focused more on the wheel offset etc Vs actual tyre fitment.

the 215 50 17 size that the Stagea has now is limiting our choice of replacement tyre.

Has anyone actually FIT a 225 45 17 to their C34 S2 , ours has the "autech" rims not sure if they are any different than others.

I just dont want to order the tyres then get em here and they dont fit.

Anyone shed any light on this?

Ok to cut a long story short, I did have a look thru the various wheel threads but they focused more on the wheel offset etc Vs actual tyre fitment.

the 215 50 17 size that the Stagea has now is limiting our choice of replacement tyre.

Has anyone actually FIT a 225 45 17 to their C34 S2 , ours has the "autech" rims not sure if they are any different than others.

I just dont want to order the tyres then get em here and they dont fit.

Anyone shed any light on this?

Stock Autech Rims are 17x7 + 30 front 17x7 + 20 rear. I run 17 x 9 +20 Wedsports SA90s with 235 45 17 with RE001s. Had floating spaces but f**ked them off. Needed nismo long bolts because of not much thread. Basically R33 GTR offset. I will not go up to 18s for daily driving only for show. Duncan runs these exact rims with Feds as far as I know.

Fitting these will be close to perfect, just dont rotate front with back because they are offset specific. You dont want to strech your tyre either, so 225s are fine for 7s. If you are from WA give chuckie a pm regarding Hankooks. Ive heard Nittos are also good and much cheaper. Buy a good set of tyres. Mine cost more than my rims but it has payed off in the long run.

Edited by dirtyRS4

225/45 will fit, but you will pay more then for a 235/45 as its a very common size, i have 235's on my autech rims and they fit fine, bulge a tiny amount but you cannot feel it when driving hard ish.

Id go the 235, can get em from $100

225/45 will fit, but you will pay more then for a 235/45 as its a very common size, i have 235's on my autech rims and they fit fine, bulge a tiny amount but you cannot feel it when driving hard ish.

Id go the 235, can get em from $100

So if your 235 fit the 225 should be fine yeah? I just don't wanna order tyres then get stuck when they don't fit

i have 235 45s on my wheels . which were rs four s 17x7 +30 . i now have 4 front autech wheels ,exact same size . nothin wrong with it . can someone tell me why the fore mentioned tire shop wouldnt do this?

Unfortunately I was away with work and someone else took the car to the tyre shop for me. The tyre shop had ordered in some 235/45/R17s for me and then when they took the car in, they rang me and said that it was illegal to fit these tyres to a 7" rim. That's all I know...

I'm away again, so can't confirm the tyre size that's on there now. I've asked the misses to check for me. She'll get back to me soon. I'm pretty sure they are 225/45/R17s and they are the tyres the compliance centre put on for me.

225 will fit on a 7in rim. You can search online for fitment charts to confirm if you want.

235 will fit but are not recommended although i don't know about ïllegal" especially when I see some of the stupidly "stretched" tyres that some people have.

So if your 235 fit the 225 should be fine yeah? I just don't wanna order tyres then get stuck when they don't fit

Yeah they will fit easily.

Ive never heard of them refusing to fit tyres before, a 265 sure but not a 235, the standard stagea size is a 225/50/17.

Just being pedantic.

I have stock Autech Rims (17x7) and the stock fitment as far as i know is actuallt 225/50/17 from factory, and is what I'm running.

I have a slightly separate question for those with a 260RS.... What size wheels can I fit??? I have the bilstein struts and have lowered them as far as I can.

It seems to me like 18x9 will not fit, so was thinking 18x8 +15 for the rear, and probably +25 for the front (matching up the stock offsets).

235/45/17 are illegal on a 7" rim, narrowest it can be legally fitted to is a 7.5" any good tyre shop should refuse to fit them to a 7 because they can get in shit if you get defected for it as they shouldnt have fitted it.

i have 225/45/17 on my rs4s rims, apart from f**king the speedo reading due to the smaller rolling height, they fit perfectly fine. my speedo just reads about 9km/h under what im actually doing

D.

I got told that 225 45 17 should be same rolling diameter as 215 50 17?? Was he full of shit?

235/45/17 are illegal on a 7" rim, narrowest it can be legally fitted to is a 7.5" any good tyre shop should refuse to fit them to a 7 because they can get in shit if you get defected for it as they shouldnt have fitted it.

i have 225/45/17 on my rs4s rims, apart from f**king the speedo reading due to the smaller rolling height, they fit perfectly fine. my speedo just reads about 9km/h under what im actually doing

D.

I got told that 225 45 17 should be same rolling diameter as 215 50 17?? Was he full of shit?
They will be near enough the same...a little bit smaller so your speedo will read a little higher.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...