Jump to content
SAU Community

Did You Use A Gasket On Your Throttle Body Adapter?

soturi

By soturi,
in Engines & Forced Induction

 Share

Recommended Posts

Sean'O Proficient

Sean'O

Posted
Posted

I used a brand new gasket set from Nissan & applied a very thin layer of silicon intake gasket just for good measure (on every gasket surface), both of which are pretty cheap, well worth spending a few bucks than loosing boost

Cheers,

Sean

Sean'O Proficient

Sean'O

Posted
Posted
So nissan has a gasket for something that doesn't come from the factory...i have gasket paper i was just thinking of cutting one out zz

Ummm, if your car didn't have a gasket when you got the car I can only assume the gentleman before you took off the plenum and didn't fork out the cash for a gasket

This is the one you're after --> http://justjap.com/store/product.php?produ...=318&page=1

You might need one of these too --> http://justjap.com/store/product.php?produ...=318&page=1 . If you don't have one, get one! A lot easier to fit it now than later :)

Your GTR service manual will take you through installing these puppies, ohh as mentioned above, I also went to Autobarn and got some of this liquid gasket just to be really sure everything is sealed up tight (only need a very tiny amount on each surface, no need to overdo it --> http://www.autobarn.com.au/AB_images/produ..._1197430754.jpg

Cheers bud,

Sean

MBS206 Grand Master

MBS206

Posted
Posted
Im going to cry.

I'm going to keep pissing myself laughing at all the idiots responding to your thread.

But to help you out, there will be no off the shelf gasket available unless you looked towards Greddy, but what would be alot cheaper, and work just as well, head to Repco/AutoBahn/SuperCrap and grab yourself a tube of gasket sealant. Put a thin layer down around everything, like around everything, around bolt holes aswell etc...

Duncan Grand Master

Duncan

Posted
Posted

personally I would go gasket paper and cut it out painstakingly. don't really trust (haha) the silicon gasket stuff.

And yes I've very surprised your kit did not come with it, especially if it was "greddy" rather than "greddy style"

soturi Community Regular

soturi

Posted
  • Author
Posted

Thanks matt....i started to wonder if anyone actually knew wtf im talking about hahahaha. Im not keen on the silicon stuff aye...but i might do a paper cut out and use some goo as well ;)

Either way ill get in touch with the company i bought it from and see if i was supposed to get one...

Thanks anyway

Aiden

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...