Jump to content
SAU Community

Bypassing heater unit - HOWTO

predator

By predator,
in General Maintenance

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

Seems like a lot of people are having the problem mentioned in this thread:

http://www.skylinesaustralia.com/forums/sh...ead.php?t=30976

Basically the cause is most likely a stuffed heater core, which involves pulling your entire dash apart, and its maybe 6-8 hours of work.

So for those that don't just want to do that just yet (but its recommended).. you can actually bypass the heater core altogether. Means you get no heat, and no proper climate control, BUT it also means you don't get leaking coolant, which can mean overheating and then the end of your engine!

For those interested: the heater core just works via coolant (which is heated from the engine) passing through a small radiator, which is in turn stores heat, and warms the car. The coolant then passes back through the firewall, and into the rest of the cooling system.

So, here we go:

1. Leave your car overnight, or at least a good few hours to let everything cool down, and water to settle back into the system.

2. First of all, remove the two hoses that go into the firewall (as shown). One is like the "in" and one the "out" coolant flow.

They are held on via clip type things. Undo the screws using a philips head or even an adjustable wrench. They can be a bitch to get to if not facing an easy direction, so slide them around if you can. A bit of coolant should come out, but when i did it, there wasn't much.

3. Use a piece of hose that will fit in between the two hoses to bridge the two. Luckily i had one that gave a tight fit @ 21mm outer diameter. Hopefully the small diameter hose doesn't cause a noticeable restriction in the cooling system(??). Probably a plastic pipe of correct size would be the most secure way to do it (didn't have one on hand).

4. Tighten up the clamps as tight as possible. Make sure its all secure, and try and angle things so the rubber hose is not too close to the engine.

5. Start her up and give it a test, check for leaks, and any sudden rise in temperature during a test-drive.

I did a short test run, and everything seemed to be normal and running ok.. but keep a razor eye on that temperature guage, and any leak from that area.

I hope this all ok, wrxhoon or the like might be able to have a quick check to see if i've done something no-no. I take no responsibilty for any damage caused by anything in this thread!

Link to comment
https://www.sau.com.au/forums/topic/31403-bypassing-heater-unit-howto/
Share on other sites
predator Grand Master

predator

Posted
  • Author
Posted

No need to plug anything.. The heater can just sit their disconnected without any problems. The heater core is just a small radiator really, where water flows in, and then straight out, heating it in the process.

Its possible you can just plug both ends of the hoses at the engine side, but i think keeping the original "flow" in and out of the engine would be best.

  • 7 months later...
JAPCAB Proficient

JAPCAB

Posted
Posted

Have a look around the firewall they must be there somewhere....i'd imagine they would put the heater in the same spot?!? Try unplugging some hoses and if you pull off the hose and see the yellow heater core plugs then you know u r on the right track. Perhaps have a look under the car - maybe they have mounted them lower if they aren't on the top

Anyone done this on a GTR? Where are the 2 hoses?
ferni Grand Master

ferni

Posted
Posted

yeah was the same place, just more crowded around the area, bypassed it for now, need to source a new heater core, i've been told copper is best, will last forever (well alot longer than a normal one)... then gotta get my dash out to replace it.... not really looking forward to it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      No chop chop of anything mate, it is what it is, plus, I don't want any air that isn't either going through the cooling stack or intake getting into the engine compartment increasing under bonnet pressure  Yeah, the Mazda Speed aftermarket intake above is less than ideal for multiple reasons, the requirement to remove the bumper every time you need to service the filter, and also smaller in diameter than the NC1 OEM one Weirdly, Mazda Speed is part of the Mazda motorsport division, "form over function" and $$$$$ for Mazda from unsuspecting punters I suspect  After some googling about them it seems they added no power, but do increase some induction noise Meh In other news, the electricians have been busy today at the house, and are back tomorrow finishing up all the security stuff and exterior lighting, they also added some lighting on the garage ceiling, which will come in handy when working in the garage when it's not freezing out there My Birdies raised garden bed also arrived today as well, which I'll put together and place tomorrow, it's a big tall Bessie, 74cm high, 92cm wide and 214cm long, this will come in handy as I am starting to get "stockpiles" of good soils from doing landscaping, some of the clean rock, namely the river stone, will go into the bottom of the bed for drainage, as well as the old Apricot tree that was out the back,  and when it's full, I'll grab another one, I will be growing enough veggies to keep me both busy as well as supplementing the shopping list I'm also awaiting another quote for a new Colourbond front fence, as the "1980 style cemented in rock edging" that was there and "fashionable at the time" looked arse, and my god, the amount of cement used to fix the rock was insane, it took 1.5 days for me to break out 12 meters of the stuff by hand, trim the bushes back to the fence line and dump it out the back of the joint to deal with at a later date,I will soon need a skip bin to tip it all Unfortunately they did alot of the cemented in rock around the joint, which I hate, so a few pallets of retaining wall blocks for around the front and back where the cemented in rock is will be required to bring it up to a standard, and look, that I will be happy with 12 meters worth of rock and cement Finished smashing the fence line and ready for a fence to be installed, yes, the lawns need some TLC and thickness, the previous owner trimmed the grass to the roots 😢, the TLC I can provide, and nature over time will do the rest And there's probably about another 40 meters worth of this landscaping abomination left to do around the front and back gardens, I'm guessing maybe 3 or 4 tons worth, tip fees for this will be a killer Meh, all in all I'm having fun and keeping busy, plus, it's good PT
    • Murray_Calavera
      Ethanol Content Sensor - Always at 11%?

      By Murray_Calavera · Posted

      If I drove to a typical petrol station, what would my choices of fuel be? 
    • MBS206
      NC MX5

      By MBS206 · Posted

      Just cut the bottom of the guard out. It's no longer got a big duct, to a sealed box, or a restriction. It has all the cold air from outside. Also, that cai you showed looks terrible. Bends are NOT good for go gos!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Like I said, "black magic" LOL In the end,  it is what it is, and hopefully, what this here knuckle head has done is an improvement and not a hindrance Not that I actually notice any negatives now, or that I will get any seat of the pants benefits when all is said and done, but best practice says I shouldn't be pulling intake air from the hot engine bay  Famous last words: I cannot see it being any worse than what it is at the moment 🤔
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      If the gases flowing in those two tracts had the same properties, you could maybe use such broscience. But the exhaust has a different composition, different normal density, different actual density (because of different normal density, and mostly because of the massively higher temperature), and different viscosity (again because of much higher temperature). Consequently, all of the fluid dynamics parameters that matter, that you calculate from these inputs, such as the Reynolds number, friction factors (for wall friction) and so on, are all incomparable.
×
×
  • Create New...