Jump to content
SAU Community

Recommended Posts

You say u just got new rims, are they decent tyres or no namers..Ive seen people have similar problems and its been el cheapo tyres that lose there sidewall rigidity..Or are just or are just crap..

If possible try a different set of good wheels/tyres, before forking more cash out...

I been chasing a wobble in my ute for ages. I got an alignment but it came back again, guy tried to blame my tyres (no doubt hoping i would buy new ones of him)... and then tried to charge me for a wheel balance a week later (why wasnt this done or checked the first time)...not wanting to throw money at another ripoff mechanic i checked it out myself ..Turns out its the centre bearing on my tailshaft stuffed, makes the whole car vibrate at 110km

But if its through your steering wheel and its not tyres its most probably front end related..ie: bushes bearings

if you told the person at the alignment shop its happened again you think they could have the decency to look around for the problem instead of charging to do the same dodgey job again...

Edited by faggywaggy
  • 1 month later...

ok lol yeh lens prettty dim, but hey.

Update car is fully insured, so only $400 excess, car is getting fixed, repainted in the front, new bonnet etc;

around $6000 worth to be fixed, will get back this wed i hope.The suspension was the major cause apparently to the shaking and noises, clunks etc; as told to me by fulcrum.

Bad mistake buying the pedders coilover rough ryder suspenion.

My tyres are the yokohama brand, pretty decent, as far as i know, rims, only xhp from bob jane t-mart, 17inch.

Just glad to get the car back soon, don't know if the ride will change though because of the accident.

Thanks for all the advice, yet to see what will happen though after i get the car back :cool:

had similar crap lately myself......dont buy Starfire brand tires (renamed Coopers....and discontinued). dunno why i bought american tires...weren't even the cheapest tires.

all was fine after the alignment, went and got new front tires, and good second hand rears (90% tread). car pulled funny afterwards. swapped the tires front and rear and all fixed....other than i had to get another balance done........no one can get the simplest of jobs right these days it seems.

good rule of thumb, dont buy american road tires, and always asume the balanceing wasnt done right if you have a shake after having work done.

My Starfires are now on the rear.........sooner they burn the better

  • 3 months later...

Update car is fixed, will post up pics soon, new front headlights and nismo clear side indicators, 2nd hand bonnet that was resprayed and radiator etc; so looking better than before, just the roof needs spraying now, starting to fade from the qld sun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...