Jump to content
SAU Community

Recommended Posts

Could be multiple things, any other symptoms other than just the light coming on? If it comes on and she doesn't notice any differences in how the car drives, it could be anything from low oil pressure (BAD thing), engine knock (she might not notice the sound that comes with this problem) or just sensors stuffing up.

I know my HICAS light comes on a lot when driving back from Sydney, but I am 99% sure there is nothing wrong with it.

If neither of you know anything more than the fact that the light comes on occasionally, I'd recommend either taking it to somewhere like Trojan Motorsports in Mitchell, or Autotech in Hume....otherwise perhaps you should swap cars for a week and see what you think yourself, try to pick up symptoms when it happens. Stop the car and listen to the engine with the bonet up, immediately look at oil pressure, water temp, etc etc

Hope that helps a little, but unfortunately a little more info is needed :thumbsup: like trying to diagnose what someone's illness is when all the can tell you is "it hurts here" and points to themself

My wife says the engine light comes on occasionally on her r33 gtr .Any ideas what it could be?

Cheers

Small world David, I work with a friend of yours (fatz might ring a bell). Loving the vmax!

Does the engine light come on and stay on or does it flicker? Do you know if she noticed any other issues when the light comes on, like loss of power or anything?

Could be something easy and cheap or could be a warning of something more drastic waiting to occur. "Warning Will Robinson" ...lol....Sorry cant be more specific as others have mentioned what else is happening if anything. Need to diagnose and best to have someone qualified than 'hit n miss' gueses. Tuning was my issue when this light flickerd ie: knock sensor.

Your Engine light is flickeringing for a real reason in most cases - This light informs you when there is a problem anywhere in the vehicles Electronic Engine Control System. This system basically includes all sensors, solenoids, valves, actuators etc. that your vehicle needs to operate correctly. The system is big and can include both engine and/or transmission concerns.

Hook it up to a scan tool and retrieve the fault codes, may not show you the exact fault but will probably point you in the right direction.

Best way to do it is check the fault codes, write them down (reference no. and description, eg. P0205-O2 sensor open circuit), erase the codes, test drive it and recheck the codes and see which ones come back.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...