Jump to content
SAU Community

Recommended Posts

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey mate,

You didnt happen to keep the two fog light / indicators off the front bumper or they went with it?

Also interested in the Manual gear surround with cigarette lighter in?

Cheers

Hey mate,

You didnt happen to keep the two fog light / indicators off the front bumper or they went with it?

Also interested in the Manual gear surround with cigarette lighter in?

Cheers

Ive got the indicators still from the front bar, yes, one lense does have a crack in it though, only minor.

Still have the gear surround too

Stevo, never received a PM off you.

Guys motor and gearbox are now out the car.

Turbo just needs to come off now, and I will grab some picks of most things.

Just waiting on some standard suspension so I can take out the coilovers and get some photos.

Sorry if I have missed alot of phonecalls of late. Please leave a message so I can get back to you. I do work a day job and have a 4 month old child so not always able to get to the phone.

How much for suspension? only need fronts, with or without springs. Spent all my cash on GTR's for the front of my GTST and they're so low wheel scrapes bumper :'(

Not willing to split the suspension sorry. You could always buy the lot and sell the rears.

Coil Pack wiring loom?

how much posted to 2906?

Ill also give you a call :happy:

Hey zebra,

Wont be separating any more engine related parts, the loom will be going with the complete motor.

Sorry bud

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...