Jump to content
SAU Community

Recommended Posts

  • Replies 199
  • Created
  • Last Reply

Top Posters In This Topic

I just got mine fitted today. I got 19x9.5 +22 at the front and 19x10.5 +12 at the rear. They pop out a fair bit at the rear, I figure once I put some coil-overs on and drop it a little they should camber in and sit a little more flush. Either that or I put some spacers on the front.

Pretty happy so far, I do wish you could fit centre caps to them though.

post-77856-1291273819_thumb.jpg

post-77856-1291273900_thumb.jpg

hey ken i need a package for my r33 GTR, 19x10 or 19x10.5 with tyres.

can you give me a qoute ? thanks

Can do 19x10.5+22 with the following KU31

255/30/19 $5200

265/30/19 $5100

275/30/19 $5200

or

KU36 285/30/19 $4900 will need to check with kumho if they any stock left

I just got mine fitted today. I got 19x9.5 +22 at the front and 19x10.5 +12 at the rear. They pop out a fair bit at the rear, I figure once I put some coil-overs on and drop it a little they should camber in and sit a little more flush. Either that or I put some spacers on the front.

Pretty happy so far, I do wish you could fit centre caps to them though.

Looks good, but needs to be lowered.

Hey guys,

More stock is arriving at the end off the week!! So buy yourself a Christmas present!!

18x10+20

18x10.5+15

18x11+18

18x9.5+22

17x9.5+12

17x9+22

  • 3 weeks later...

What is the price difference between 18 x 10.5 and 19 x 10.5?

and do you know if you need gaurd rolling or anything for R33 GTR to fit 10.5's all round?

cheers

Daz.

Only $300, i don't think guard rolling is required for a R33 but the R32 it's a must. We also have 18x10+20 in stock if you want..

  • 1 month later...
  • 4 weeks later...

How much for a set of 18 by 9.5 +22 offset without tyres including shipping to Hamilton, New Zealand?

Freight would be a killer, if you can get a quote on your side it could be cheaper. i'll find out and advise on our side

hi mate looking for 18x10 et 35 and 18x9 et 35 as i need to put adapters to fit my car

They come in those sizes you want, the closest is 18x10+20 and 18x9.5+35 or 18x9.5+22. Not sure by what you mean adaptors? Do you mean spacers?

hi mate sorry should have explained, im looking to put them on my audi and need to fit an adaptor plate to do that. it usually knocks 15 off the et. looking to get rim size/offset close to 18x8.5/9.5x et13 and 18x10 et19 so im looking at offsets around et 28 and 35 before fitting the adaptor. sorry if i rambled on

hi mate sorry should have explained, im looking to put them on my audi and need to fit an adaptor plate to do that. it usually knocks 15 off the et. looking to get rim size/offset close to 18x8.5/9.5x et13 and 18x10 et19 so im looking at offsets around et 28 and 35 before fitting the adaptor. sorry if i rambled on

Ok the closest is in 5x114.3 is as following unless you want the normal TE37 which has a lager selection of offsets and iszes

18.9.5+35 or +22

18x10+20

Regular TE37- they don't come in 18x10 only 10.5+15 or +22

18x8.5+22 or +30

18x9.5+22 or +35

  • 2 weeks later...



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...