Jump to content
SAU Community

Tomei Rb25 Ser.1 Poncams Specs Needed

Takoon

By Takoon,
in Engines & Forced Induction

 Share

Recommended Posts

Takoon Rookie

Takoon

Posted
Posted

Hello guys,

have these PONCAMS

http://www.nengun.com/tomei/pon-camshafts

Part Number: 143020 "ECR33 Series 1 (RB25DET) - Duration: IN,EX 256 Lift: IN,EX 8.5mm Skyline - R33 GTS-t S1 - ECR33"

and need the technical specifications to adjust them. Only found the duration, but not the opening and closing times as for example you can see here:

http://www.jdmlevin.com/files/CamshaftData...akeCamshaft.jpg

May anybody help me? I searched in the web, but without any results.

Thanks and best regards

vik

tridentt150v Grand Master

tridentt150v

Posted
Posted

Tomei poncams are a drop in replacement and have optimal timing standard. That is, you set them up with 0 degrees advance. You can try a degree or so, but I doubt you will see any improvement over zero - in fact you will more likely see a decrease in power and efficiency.

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

Same reason people upgrade camshafts in any vehicle, more duration and more lift over standard camshafts.

Procams are once again more lift and more duration over Poncams.

Edited by PM-R33
tridentt150v Grand Master

tridentt150v

Posted
Posted

Do a search, I remember reading a thread on here? that showed no difference in the top end, but a good mid range improvement of around 10-30kw depending on supporting mods. This is pretty much exactly where you need it IMO. Plus if your engine is breathing better it has to be more efficient.

jarrod83 Community Regular

jarrod83

Posted
Posted

did you lose any boost response? from the dynos i have seen between different cars i thought the cams lost down end response without any descent gains in the top end.. i'll have another search for that thread, i was searching 256 dynos before but didnt get anything descent.. can you remember any keywords

Cheers

Jarrod

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

Here's my old thread:

http://www.skylinesaustralia.com/forums/Dy...ns-t270208.html

As you can see no drops in power anywhere with the headwork. Obviously you have to consider I did a bit more than just the Poncams though.

Edited by PM-R33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...