Jump to content
SAU Community

Need Help!

myRB25DETT

By myRB25DETT,
in Victoria

 Share

Recommended Posts

myRB25DETT Community Regular

myRB25DETT

Posted
Posted

hi gangs...

long story short, having problem putting the rubber joiner back on for the manifold inlet, what do i need to do?seems to hard to push it back down and slip it in at the other end. any other way i can connect it back?? rubber too stiff or hard..!! picture below will tell u what i meant..btw, i was trying to change spark plugs before i got stock to this problem..car been out of road for a week now..anyone from westside gimmi a hand for a can of VB or something??

cheers guys..

post-59132-1272080939_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/
Share on other sites
33gtst Proficient

33gtst

Posted
Posted

have you connected all other end clamps? if so undo them a little to allow for some movement. It should just slot back in unless everything else is locked tight, with a bit of a wiggle a bit of lube and a few choice words.

Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/#findComment-5197815
Share on other sites
myRB25DETT Community Regular

myRB25DETT

Posted
  • Author
Posted (edited)
have you connected all other end clamps? if so undo them a little to allow for some movement. It should just slot back in unless everything else is locked tight, with a bit of a wiggle a bit of lube and a few choice words.

i havent put the hose clamps back on yet..not enough gap or space to wiggle the other end...not even enough space to push it down and slot back in.!! really frustrating me now!! i got it out easy at the first place but putting it back in is an asS thing to do!!!

anymore trick to slot it back in guys??

Edited by myRB25DETT
Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/#findComment-5197825
Share on other sites
Omurru Veteran

Omurru

Posted
Posted

what do you mean by not enough room to push it back down and slot it in, Try completley disconnecting the other end of the pipe so you have more movement to push it on then connect the other end when the throttle body end is on....where bouts are you?

Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/#findComment-5197868
Share on other sites
arep3 Experienced

arep3

Posted
Posted

sorry mate but the only way to get it on is to persevere at it and have plenty of patience. i always have trouble with my piping yet i eventually get it back on. Im missing a couple fingers off my main hand and i can do it.

Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/#findComment-5197883
Share on other sites
myRB25DETT Community Regular

myRB25DETT

Posted
  • Author
Posted
what do you mean by not enough room to push it back down and slot it in, Try completley disconnecting the other end of the pipe so you have more movement to push it on then connect the other end when the throttle body end is on....where bouts are you?

well as u could see on the photo,i got the left side out, but the other end i couldnt, no way i could disconnect completely at the other end..pretty much dead end...i live in altona..next to altona beach or altona station...

Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/#findComment-5197938
Share on other sites
myRB25DETT Community Regular

myRB25DETT

Posted
  • Author
Posted
There is no real "trick", just have to make it go in :blink:

Sometimes a tiny bit of oil around the inside edge can help

i know what u mean, but thats not even close to my case, my hose is not even facing evenly with the other end/inlet that you can just lube it and slot it back in...hose is slightly few m.m. above the inlet manifold and tried pushing it down to face the inlet and so i can just slip it thru but thats where the problem is, cant push it down far to face the inlet and then in...argggg

Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/#findComment-5197953
Share on other sites
myRB25DETT Community Regular

myRB25DETT

Posted
  • Author
Posted
In your OTHER thread, it seemed to be all connected.

Oh well then, PM me your address and I'll come to you.

sorry to confuse u, but nah its not connected, and yeah thanks heaps for the offer....PMed u already for the add...let me know what i owe u!! :blink: cheers for that!!

Link to comment
https://www.sau.com.au/forums/topic/317966-need-help/#findComment-5197969
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...