Jump to content
SAU Community

Recommended Posts

Hi,

My bro just got his new line and we were intrested to see what the turbo looked like to compare to other bros turbo.

and we noticed that the fins look different and are bent and chiped ?

is this a problem ? do we need a new turbo ?

their doesnt seem to to be and problem when driving, all though it sounds different when it spools up you can hardely hear it, it doesnt make the whistling sounds like the pod but its a different sounds ?

Thanks,

by the way its on a 95' gtst

(i'll post pics later tonight)

Link to comment
https://www.sau.com.au/forums/topic/31865-damaged-turbo-wheel-r33-gtst/
Share on other sites

Well if you go two turbos off the same series motor.

then you can bet your dollar it's a bit damaged.

chipped is not all that good.

Fins can have a 'bent' look. it might just be the wheel.

I dunno what the differences are between the two though... series I vs II.

but i think there was something a tad different.

either way for a new one you only looking at $400

hi

I think I might be having a problem with my turbo too...

It looks ok the last time I checked it..

but at higher speeds.. about 200km/h + there's a really loud shhhhhhhhhhh sound... quite unnatural...

not sure whether something's wrong with the turbo or the blow off valve...

I'm running on standard turbos and turbosmart BOV..

anyone experienced this before?

thanks

That turbo has ingested something, but if it still goes, then keep using it, unless you really want to upgrade. These turbos are generally, not very servicable or rebiuldable. But they are quite tuff. It could keep working fine for years to come. Look at it this way, you only found the damage, coz you looked....you didnt hear any strange noises or see oil or anything.

You can if you want, buy a new comp wheel and get it fitted and balanced, but Personally I woudlnt bother, the time and money isnt worth the problem if the wheel fails. I doubt you would notice the drop in power at all.

I have been playing (that should read, trying to fix:P) a couple of rb25det turbos, and have found the following info....

If you break the seal plate, you can't get a new one (oh no!) If you own a lathe, you can make a new one (doing that now actually)

The turbine is not able to be serperated from the shaft, and is balanced as a single unit

The comp wheel is balance as a single unit, and therefore, you can generally swap wheels with not too much hassle (if you dont balance them, you will get a shorter turbo life, but generally, you will get away with it)

IF you pull apart totally the bearings, (they are not captive bearings) the balls will fall out and roll across the floor, into the drain, cracks in the concrete etc etc, bye bye turbo....

If you can feel shaft play sideways or end ways, the bearings are worn, but if your lucky, you can still have some more room to tap in the centre peice of the comp wheel side bearing (under that damn seal plate im afraid, hard to take them out without breaking them) and get rid of that play, and get another 100 000 kays out of a unit.

Worn bearings and side play and end play in the shaft leads to misalignment of the seals, which of course leads to oil leaks, smoke, etc....

by the way, I picked up a second hand turbo for $200 on the weekend and fitted it to my twin turbo rb25dett VL and it fixed my problem.

So as you can see, spending money at a turbo shop rebiulding a stock rb25det turbo is not a financially rewarding thing to do. Its better to just source a second hand one.

I had two good turbos, untill one started leaking oil into the air intake. Upon trying to fix that turbo, i broke the seal plate. Bought a buggered turbo for $70 and broke the seal plate in that trying to get it out too! :P (DOH)

Bought another good turbo for $200 and fitted it and no worries.

Now im making two new seal plates, using two new o rings, and setting up the bearings in those two turbos again, to see if i can get those turbos operational again. If not, ill turf them:P

black smoke is fuel not oil.

why should it boost higher than standard boost? you got a bleed valve hooked up?

If you have and its refusing to boost very high, it could be any number of alot of other things. I've never seen a turbo that is in such a state that it wont boost higher than standard boost, unless its really stuffed (turbine hitting houseing, seized bearings, etc)

They seem to either work fine, or dont.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I am getting the same issue. Did you resolve it? I just got it after installing my new super coppermix and literally the same issue, new fork, new 18mm carrier, release bearing that came with the kit and replicated the exact same sound. 
    • If you like - I have the STL files so I can email em. There's a couple of gotchas (i.e the holes are not threaded so you might need/will need) to utilize some M3 melt-in threads for some of the points. However if you want to be super accurate, and are willing to remove your calipers and your SHOCKS it's a really good tool. You also might need to scale the part that measures the tyre width a bit wider. It defaults to a 7.5in tyre and I mean who is running that. Luckily with the magic of CAD this is very easy to rescale.
    • jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
×
×
  • Create New...