Jump to content
SAU Community

Recommended Posts

ok its a r34 gtt with basic bolt on mods on 12psi

first thing i noticed was on mainly cold starts on idle it stutters and pops at the exhaust

then i noticed on gentle driving it accelerates smoothly, but once i put my foot down it stutters badly and goes no where.

this happens when i hit full boost mainly

i was thinking shit spark plugs?

would appreciate any help asap

Link to comment
https://www.sau.com.au/forums/topic/318859-car-stuttering-badly/
Share on other sites

the pops in the exhaust have been there for aslong as i remember.

the stutter on idle on cold starts i noticed it about a week or 2 after the timing belt and water pump were replaced with new ones.

this part "on gentle driving it accelerates smoothly, but once i put my foot down it stutters badly and goes no where.

this happens when i hit full boost mainly" i noticed it months ago but has been getting worse ever since...

i have changed the intake pipe a couple of times during the past few months (from rubber to steel to rubber and now rubber with steel piece in it.

i also changed the afm (mine broke) and put stock airbox back on. i did this a few days before the timing belt was replaced

Something else you should consider is the factory 12.5psi boost cut.

Will cause major issues while at full boost.

Although, it does sound like a vacuum leak causing the dodgey idle etc.

Check for vacuum hoses that you might have not reconnected and check to make sure the timing has been set correctly. You may have just one problem causing everything or you may have a few problems all working together.

Hey There,

I had the same thing happen to mine after having the timing belt and water pump done, turned out it was the ignition timing was out by a quite a bit. I was thinking coil packs,sparks plugs,fuel pump etc $$$$ before finding the timing was out, I'd get your timing checked before running out and spending money unnecessarily. Hope that might help. cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, you're wrong, and you've always been wrong about this. The Nismo has 2 sets of openings. One is a real 2-way, and the other is a 1-way. There is no 1.5-way possible with the ramps that they offer. A real 1.5-way does exist. That Cusco stuff I posted is a prime example. If the forward drive ramps are, say 55°, and the overrun ramps are, say, 30°, then you will get about half as much LSD effect on overrun than you do on drive. It is real, it realy works. OK, you're slightly right. The Nismo has 55° and 45° ramps on the 2-way, so it does offer less LSD effect on overrun. But, I think that just means that they've (probably) sensibly established that you do not want actually equal LSD effect on overrun. You just want "quite a lot, but not quite as much as the drive LSD effect".
    • Just wanted to unearth this and post my baby with the new front ❤️😝 Took her to my wedding rehearsal today. Next up is getting wide skirts (after wedding)
    • Yea, that is what I was getting at in my ramblings too. The nismo one actually is a 1.5 way and a 1 way. They don't do a *2* way because a true *2* way would have equal ramp angles. Or is that a true 1.5 way? Realistically I think a "1.5 way" does not actually exist. A diff can either lock in two directions or one. It also doesn't help that a LOT of people in Australia speak about 1.5 way diffs are referring to their 1 way diff.
    • Well, the trouble with that ^^ is: The configuration shown is absolutely a 1-way, not a 1.5-way. There is no way that a 1.5-way can be said to offer LSD action only on acceleration. If Nismo cannot get that right, then it is impossible to believe their documentation. That ^ is not a 1.5 way setup. That is a 1-way.   And so now I have allowed all doubts to flourish and have gone back to look at the MotoIQ video. I originally made the mistake of believing him when he said "this is a 1.5-way" at the ~6:10 mark. Because what he did was take the gear assembly out of the 2-way opening and just rotate it one place to the left to drop it into the 1-way opening. When he dropped it in there, the cam was "backwards" compared to the correct orientation shown in all other photos of that config. The flat shold have been facing the 1° ramp side of the opening, not the 55° ramp side. And I thought, "gee that's cute", but I was concerned at the time, when he put the other ring back on, that the gap between the rings looked like it was wider then in the 2-way config. And then I said a lot of things in my long post on Tuesday that could only make sense if the guy from MotoIQ was correct about what he'd done. BUT... I have now done my homework. I grabbed a frame of the video with the 2-way config, and then grabbed another with the "1.5-way" config, snipped out the cam and opening of that frame and just pasted it direct on top of the 2-way config. I scaled it so that the triangular opening was almost exactly the same height in both. AND.... the gap between the plates is wider with the cam installed in the triangualr opening backwards. That is.... it cannot go together that way. There would be massive force on the plates all the time, if you could even reassemble it.  So, My statement on the matter? The Nismo diff is actually only a 2-way and 1-way. There is no 1.5-way option in it, regardless of what they say. Here's a photo of a real 1.5-way ramp opening from Cusco (along with the 1 way option). And the full set of 1 through 2 way options from their racing diff, which is not same-same as what we'd typically be using, but...the cams work the same. A little blurry, but it comes from this Cusco doc, which is quite helpful. AND.... Cusco do in fact do what I suggested would be sensible, which is to have rings that do 1 and 1.5, and 1.5 and 2. Separately.  
×
×
  • Create New...