Jump to content
SAU Community

Boost Gauge + Water

johnnysr33
 Share

Recommended Posts

Hanaldo Grand Master

Hanaldo

Posted
Posted (edited)

Well just installing the gauges you could do yourself for free, it's easy as.

$6000 would include the cost of turbocharging your engine so as to actually make a boost gauge useful.

*EDIT* I am assuming your car is non-turbo considering you posted this in the naturally aspirated section...

Edited by Hanaldo
Hanaldo Grand Master

Hanaldo

Posted
Posted (edited)

Yeh my advice would be to install it yourself mate. The hardest part is finding a place in the firewall to feed the wires. It's so easy to do, it really isn't worth paying ~$150-$200 to get someone to do it for you

Edited by Hanaldo
johnnysr33 Apprentice

johnnysr33

Posted
  • Author
Posted

its a turbo.. sorry for posting this in the wrong section!! yeah i have considered doing it myself but just a bit scared, my mate done it to his skyline now all his dash lights are flashing on and off and random times :S but ill read into it some more and if im confident enough then ill do it if not wouldnt mind paying for it to get pro done. thanks heaps for the advice!!

mad082 Grand Master

mad082

Posted
Posted
its a turbo.. sorry for posting this in the wrong section!! yeah i have considered doing it myself but just a bit scared, my mate done it to his skyline now all his dash lights are flashing on and off and random times :S but ill read into it some more and if im confident enough then ill do it if not wouldnt mind paying for it to get pro done. thanks heaps for the advice!!

well then make sure you don't let your mate anywhere near your car.

for the water temp gauge you need to make sure you have the temp sender that goes with the gauge. without it it won't work. also you will need an adapter to put it into the radiator hose.

boost gauge is very easy to do. only slightly hard bit is wiring up the lights, but you could always just run all the hose through so the gauge works and then just take it to an auto electrician and them them to sort out the wiring. should only take them a few mins and not cost much at all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • Kinkstaah
      Wheel Sizes & Offsets For Skylines

      By Kinkstaah · Posted

      If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...