Jump to content
SAU Community

Recommended Posts

And i know ive already topiced about it, but coilpacks are going!.

I'm already saving up for replacements but today the warning lights came on and havent left like they normally do! And i just need the car for about a week until i have the money for new ones.

I have a 2nd hand set from my mates car (60000k) in now, and my old set (150000k) in my garage, im wondering if there is a way to locate the one that seems to have died without trial and error?

I could educated guess it as 6th cylinder (from front) or 4 or 5 as they are gonna be the hottest right? But my friend said (not sure how true this is) that you could test each one using a voltmeter and testing the voltage through each one.

Another thing i thought of was perhaps unplugging each one individually while the car is running, and which ever one DOESN'T change how the car runs is the dead one! But i dont know if this is going to damage anything since plugging and unplugging things while connected to battery never agrees with me!

What are peoples thoughts and ideas? I really need the car as its my daily and i will have the problem sorted asap. Just dont wanna drive around with a dropped cylinder/misfire all the time.

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/
Share on other sites

The combination of the lights i think that indicates an ignition problem?

The problem slowed once i replaced my old bad ones with these 2nd hand ones but now seems to be permanent.

At first the engine light comes on, followed about a second later by the slip and traction control lights.

I'm told thats the combination usually meaning coilpacks, and that coilpacks are a very likely problem in our cars.

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5217249
Share on other sites

ahh i know everyone is misfire / coilpack / cas mad these days

but what warning light are you talking about?

from memory no warning light will come to indicate dead coilpacks etc

keep the car running and take coilpack plug out one by one, if the one you pull out makes no change then thats the one thats failed

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5217253
Share on other sites

In driving it to shops and back it didnt come up this time, which is good news that its not completely dead just yet, but now im stumped for ideas on trying to find the crappy (or crappiest) one of the lot if it doesn't fail again.

Just wondering if there is anything i can do to see if one is likely to fail (while its still working) or a way to make it make (like heat it or something) any ideas?

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5218194
Share on other sites

hmmm... slightly intermittent problem? Have you checked the harness to the coils? It may have gone hard and brittle and may not be putting the electrical charge through to the coils. Hence, when you pushed it all back together when you installed the 2nd hand set it got better for a while...

Just my 2 cents on what to check...

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5218203
Share on other sites

At first the engine light comes on, followed about a second later by the slip and traction control lights.

I'm told thats the combination usually meaning coilpacks, and that coilpacks are a very likely problem in our cars.

that is complete bullshit! there is no 'combination of lights' that indicate dud coil-packs. even in diagnostic mode there is no magic 'dead coilpack' sequence.

Another thing i thought of was perhaps unplugging each one individually while the car is running, and which ever one DOESN'T change how the car runs is the dead one! But i dont know if this is going to damage anything since plugging and unplugging things while connected to battery never agrees with me!

this is 100% the easiest way to find the dead coil-pack (if that is in fact your problem). with the car idling remove them one by one. as you remove one the car should start missing more heavily. when you remove the one that doesn't change the idle at all you have a winner.

the engine check light and other warning lights coming on is a worry though. and no they are in no way telling you of an ignition problem. the engine check light usually is telling you that you have no oil pressure. but with many coming on it sounds like possibly some other electrical problem.

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5218242
Share on other sites

i stick with my original thoughts, and thanks for beer baron agreeing

there is no engine check light for dead / mangled coil packs

it sounds like, at a guess

stutter, followed by SLIP TCS coming on is that your TPS is mangled, loose, fault, out of range

the engine would stutter if the TPS goes out of range or reports whack values

SLIP and TCS would fail if TPS goes out of range / fails as it needs to know how far throttle body is open to function and guess "wheelspin" conditions

so check your basics, check the TPS, check the throttle body, run stock ecu diag with consult port / cable / diag

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5219301
Share on other sites

i have the same problem in my r34 gtt. you could run the engine diagnostics using this diy:

http://www.skylinesaustralia.com/forums/Re...de-t266512.html

if you get the signal 21 it means ignition problem, which is likely to be coilpacks.

the problem with taking one coil out at a time is that it already has to be failing, ir: not running normally. mine pops like a wrx but once it gets above 2500-3000rpm it goes away, most of the time. don't like doing that tho cos it putting stress on a stressed engine.

people have all sorts of ideas like taping the coilpacks, or covering them with silicone gel stuff to insulate them, so the charge doesn't arc to the engine block. does your problem happen often? cos mine usually fails round 10 mins into the first trip of the day...

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5219303
Share on other sites

Mine happens on and off, if it happens will be about 10 mins in similar to yours.

Sometimes if i pull over and let the car sit engine off it wont come back.

But sometimes it does.

Normally letting the car cool down over a few hours will definately get rid of the fault.

I just played around with coilpack wiring harness/plugs and didnt notice one faulty (althrough i couldnt get to coilpack 4 or 5) but after playing with all the plug and wires and restarting engine the lights where gone, but came back 10 mins later on a drive.

When i got back i left engine running, played with plugs again, (at this point lights were still on) then restarted engine, to which only the TCS and SLIP lights came on (not engine light like normal) then immediately restarted engine again and no lights came on, and stayed off for 5 mins at idle.

So i'm stumped, i think i just need to get new coilpacks (since they are needed even if it isnt the problem) and see if it goes away, if not then ill chase the other ideas.

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5219476
Share on other sites

craig, do they happen to come on more often when its raining...?

i had the same problem with what i said earlier, i was told by the importer when i had it that it happens as they die and will occur more frequently..

i just had my coilpacks replaced and spark plugs and no problems runs like a whole new car

before u go spending $600 take it to the mechanic and get him to diagnose it properly... not much u can do but pay some $ either way lol

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5219487
Share on other sites

i stick with my original thoughts, and thanks for beer baron agreeing

there is no engine check light for dead / mangled coil packs

The neo powered stagea threw an intermittent check light when the coils were on their way out. Once replaced it resolved so I believe it is possible. There was no checklight with the R33 when the coils were done.

I am not sure if the later model ECU has the capacity to throw the checklight or it was something coincidental but to the best of my knowledge it was the only part changed.

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5219505
Share on other sites

Mine happens on and off, if it happens will be about 10 mins in similar to yours.

Sometimes if i pull over and let the car sit engine off it wont come back.

But sometimes it does.

Normally letting the car cool down over a few hours will definately get rid of the fault.

I just played around with coilpack wiring harness/plugs and didnt notice one faulty (althrough i couldnt get to coilpack 4 or 5) but after playing with all the plug and wires and restarting engine the lights where gone, but came back 10 mins later on a drive.

When i got back i left engine running, played with plugs again, (at this point lights were still on) then restarted engine, to which only the TCS and SLIP lights came on (not engine light like normal) then immediately restarted engine again and no lights came on, and stayed off for 5 mins at idle.

So i'm stumped, i think i just need to get new coilpacks (since they are needed even if it isnt the problem) and see if it goes away, if not then ill chase the other ideas.

Exactly the same symptoms as mine. Did you follow the diy above? whenever the malfunction indicator light comes on an error is logged, you can find out what the error was from that. might be worth doing to check there's only one error coming up

Link to comment
https://www.sau.com.au/forums/topic/319446-coilpacksssss/#findComment-5219610
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...