Jump to content
SAU Community

Recommended Posts

Here's my story...

2 Years ago I finally purchased my dream car, R33 GTR its a 1996 V-Spec

Now practically as soon as I purchased it, the motor went BANG! I was heartbroken.

Reluctantly I began sourcing parts for the rebuild! I wanted to do it once, do it right, so the entire process took quite a while and my dream was simply left parked in the garage for a year while the engine and parts were being sourced and put together.

So in November 2009.. After a long wait, and a few dramas in between the car was all back together in one piece, all was going well.

I ran in the motor, and took it fairly easy for the first few months. I have covered 3,000km since the rebuild, running standard ecu, standard boost for the entire period.. yesterday I took it to my tuner, to connect a boost controller so we could run some more PSI through those turbos!

All was well, then suddenly noticed a horrible rattling sound from the engine... the type no one should ever hear!

Went back to my builder today and my worst fears were confirmed.. suspected conrod bearing!

I'm absolutely devastated! I'm not sure what to do... Having bought my first home recently means I don't have enough funds to have it all pulled apart and fixed again!

In total over the past 2 years I have sunk around $50,000 into this car (including purchase price)

Here's a run down of parts:

Eagle Rods

N1 Water Pump

Nitto Oil Pump

Extended Sump

Arias Pistons & Rings

ACL Race Series Conrod Bearings

ACL Race Series Main Bearings

HKS Dump Pipes

Nismo Exhaust

Nismo SP Suspension

Nismo LM GT1s

Nismo Engine Mounts

Nismo 320km Dash

Ross Harmonic Balancer

Garrett GT2860R-5S Turbos

Nismo Coppermix Twin Plate 640PS

Toyo Proxes T1R 275/35ZR18

All parts purchased BRAND NEW

Not Yet installed:

Apexi Power Fc

Sard 700cc Injectors

So my question to you is..

Should I keep it locked up for another year or 2 while I save $$ to fix it

Sell it? If I was to try to sell.. realistically speaking whats the best I could hope for?

Strip it?

Either way its a lose, lose situation.. i'm simply devastated! :yes:

Link to comment
https://www.sau.com.au/forums/topic/319575-heartbreak-again/
Share on other sites

Your engine builder needs a kick in the teeth for one. This should not happen to a freshly build RB26 especially if you havn't been giving it any track time.

At this stage, I would say put it away for a rainy day, continue the build slowly. Your too far into it at this stage to simply sell up, you'll loose thousands and thousands miss out on the gradification of all the money poured into it this far.

Either tuner abuse or poor engine build - I can't see how it could just chew a bearing at its own accord.

If the builder put this engine together for you, isn't it the engine builder's problem? The builder should stand by his work. I can't see how a fresh new engine can lunch a bearing ... unless he recycled the old ones?

:yes:

That sucks mate! Especially with all the shit you've been through, including the break in! As said, the builder should be coming to the party in some way. I wouldn't sell it, you'll lose way too much then regret it down the road. If it were me, I'd just keep it and work on it slowly rather than get rid of it completely

If the builder put this engine together for you, isn't it the engine builder's problem? The builder should stand by his work. I can't see how a fresh new engine can lunch a bearing ... unless he recycled the old ones?

:yes:

I've had the discussion of liability with him, he argues if it had been of his doing, then this would have happened within the first couple of hundred kms

I'm going to lodge something with consumer affairs/fair trading and see what comes from it...

but to be honest I don't think I can go through the whole process again.

I've had the discussion of liability with him, he argues if it had been of his doing, then this would have happened within the first couple of hundred kms

I'm going to lodge something with consumer affairs/fair trading and see what comes from it...

but to be honest I don't think I can go through the whole process again.

err, I was in engine reconditioning for 20 years and we would always stand by our engines.....that comment is a load of cock.

if he used s/h bolts or didn't torque them correctly or didn't check brg crush before assembly, etc, etc, etc........then this can happen months done the road.

what did your tuner do?

have you checked the simple things like oil level?

if you haven't been launching it and your tuner hasn't got a happy foot, I'd be asking questions of the builder.

Speak to OCBA first.

Oil level and pressure is perfect!

I haven't launched it ever and not once took it over 7000rpm, been waiting to install support mods before giving it a real drive.

like I said, see someone at OCBA first, but I'd be telling him to either fix it or you'll get someone else to fix it and send him the bill.

Did he make you sign a waiver that none of his work would be guaranteed....even that piece of paper wouldn't hold any weight if it hasn't been too long since the build.

Whether a business offers warranty or not for their work is besides the point, the law requires them to stand by their workmanship..........unless of course it's a race car then I suppose it becomes a moral obligation.

isnt it called statutary warranty?

if u pay $5000 for a tv and it last 2 yrs then u have a leg to stand on..

give it a go man! whats the worst tgey could say no? and be at the same point!

yeh i've heard about it before, definitely going to be following it up

Sorry to hear about that David! My vote goes towards chucking it in the shed until you can afford to fix it up rather than selling it - atleast one day you'll be able to enjoy it instead of offloading it now for next to nothing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...